Traxxas Front Bulkhead (Black) Slash / Bandit / Rustler / Stampede

This is a Stock Replacement Front Bulkhead used in lots of Traxxas vehicles.
The front suspension arm hinge pins go through this piece.

FEATURES:
Black nylon building

CONSISTS OF:
One front bulkhead

NEEDS:
Nothing. This is a direct replacement part.

SPECS:
Length: 73.6mm (2.90")
Width: 41mm (1.62")
Height: 29mm (1.14")

COMMENTS:
This part is used on the list below vehicles:
    Rustler, Bandit, Stampede, Nitro Rustler, SRT, Nitro Stampede.

You will enjoy this thing if you have the thing earlier discussed.

Tie Bar Fiberglass

This is a Firberglass Tie Bar by Traxxas for the SRT

FEATURES:
Fiberglass Building

CONSISTS OF:
One Tie Bar

NEEDS:
Suspension Pins (TRAC4940)

SPECIFICATIONS:
Length: 98.4 mm (3.875")
Width: 7.9 mm (0.3125")
Density: 2.0 mm (0.082")

COMMENTS:
None

Right here is a fantastic item that several others have actually purchased the exact same time.

Front Bearing Carriers, For Slash 2Wd, Nitro Slash, E-Rustler &

These are Optional Front Bearing Providers for the Traxxas Electric
Rustler, Stampede and Bandit

The Front axles fit into these bearing carriers.

FEATURES:
Black nylon building

CONSISTS OF:
2 Front bearing (center) carriers
2 RPM decals

NEEDS:
(4) 5x11mm bearings, if required use (2) DTXC1547.

Want another fantastic item to match the above stated item?

Skid Plates Front & Rear (S)

This is a replacement set of skid plates for the Traxxas Stampede.

FEATURES:
Made from black molded nylon
For the Traxxas Stampede

SPECIFICATIONS:
Length of front plate: 5 5/8"
Density of front plate: 3/16"
Width of front plate: 2 1/8"
Length of rear plate: 4 3/8"
Density of rear plate: 1/8"
Width of rear plate: 2 1/8"

CONSISTS OF:
(1) Front skid plate
(1) Rear skid plate
MDJ 3/25/95 ¦-)

The listed below item also pairs really well with the item being reviewed.

Caster Blocks, For Traxxas Electric Slash, Stampede, Rustler, Ni

These are RPM 30° Front Caster Blocks for the Traxxas
Electric Stampede and Rustler.
These blocks install to the front A-arms and is exactly what the
guiding knuckles connect to.

FEATURES:
Nylon building, black in color
Stamped right and delegated insure correct setup

CONSISTS OF:
2 RPM 30° Front Caster Blocks

NEEDS:
Assembly in between A-arms and guiding knuckles

This item praises the above reviewed item.

Front Shock Tower, For Traxxas Slash/Rustler/Stampede/Bandit

This is the optional RPM Front Shock Tower for the
Traxxas E-Stampede, E- Rustler, Bandit & Nitro Stampede.

FEATURES:
Plastic building
Black in color

CONSISTS OF:
One Front Shock Tower for the Traxxas E-Stampede, E-Rustler, Bandit
    and Nitro Stampede

NEEDS:
Installation on the automobile

SPECIFICATIONS:
Width: 3.26" (83mm)
Height: 2.91" (74mm)
Density: .27" (7mm)

Several others have actually bought this item together with the item that you are presently reading about.

Heat-Treated, Carbon Steel Front King-Pins, For Traxxas Slash /

This is a pair of ST Racing Concepts Polished Front King Pins
for the 1/10 scale 2WD Traxxas Slash.

FEATURES:
CNC machined, heat treated and polished steel building

CONSISTS OF:
Left and Right King Pins for front suspension

You will enjoy this thing if you have the thing earlier discussed.

Suspension Pins 44Mm Slash Rustler / Stampede / Bandit

This is a pair of chrome suspension pins used to hold the front suspension arms
on the TRAXXAS SRT, NITRO STAMPEDE, and NITRO RUSTLER.

Includes: two chrome suspension pins and two "E" type retaining clips.

Requires:absolutely nothing parts are a direct replacement.

Specs:3mm x 44mm pins are notched for the 3MM "E" type retaining clips at each
end. WLG 9-29-97