Traxxas Front Axles (2) (R & S)

This is a Pair of Stock Replacement Front Axles for the Rustler and Stampede.
These are located in the front steering blocks.

FEATURES:
Steel building and construction
Natural color

INCLUDES:
Two front axles

REQUIRES:
Nothing. These are direct replacement parts.

SPECS:
Length: 32mm (1.26")
Diameter: 5mm

COMMENTS:
These will not work for the nitro variations. For that axle, use
    TRAC2536.

This is a fantastic addition to the thing presently being talked about.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building and construction
Blue rubber dirt guards

INCLUDES:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside size: 3/16" (5mm)
Outside size: 7/16" (11mm)
Width: 5/32" (4mm)

Frequently purchased with the thing that you are presently reviewing.

Hex Wheel Hub 2.5 X 12Mm Rustler / Stampede / Slash

This is a Hex Wheel Center Set for the Traxxas Rustler and
Stampede. These parts have actually more balanced out than
the stock hex wheel hub set (TRAC6044).

FUNCTIONS:
Gray plastic building and construction

INCLUDES:
Two wheel centers
Two 2.5mmX12mm axle pins

SPECS:
Hex size: 12mm
Width: .32" (8mm)

The listed below thing additionally pairs really well with the thing being talked about.

Stub Axle Pins (4)

These are replacement stub axle pins for the Nitro Buggy, Nitro Street, TRX-3,
Rad 2, TRX-1, Hawk 2, and Blue Eagle LS II. These pins slide through the axle
and hold the wheel to the axle.

INCLUDES:
4- stub axle pins

WAJ
1/30/94

This thing is regularly purchased with the above pointed out thing.

Teflon Washers 5 X 8Mm (20)

These are Replacement Washers from Traxxas.

FEATURES:
Black plastic construction.
Used on the axles and in the transmission.

INCLUDES:
(20) Washers

SPECS:
Size: 5x8mm
Density: 0.5mm

Frequently purchased with the thing that you are presently reviewing.

Hex Hubs & Axle Pins Slash

These are the replacement rear wheel adapters for the Hawk, Hawk 2, Bullet,
Sledgehammer, Eagle, and Blue Eagle LS. These are hex nuts that connect the
rear wheels to the axles.

INCLUDES:
2- plastic hex collars (wheel adapters)
4- stub axle pins

WAJ
1/16/93

This is a fantastic addition to the thing presently being talked about.

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Sturdy Driveshaft Assembly for the Slash 4x4 from Traxxas

FUNCTIONS:
Black plastic and steel building and construction

INCLUDES:
Rear driveshaft assembly
Screw pin

REQUIRES:
Setup on vehicle

Here is another thing that praises the thing being talked about.

4Mm Flanged Nylock Nuts (8)

This is the Traxxas Flanged Nylon Locking Nuts.

FEATURES:
Steel serrated building and construction

INCLUDES:
Eiqht 4mm flanged nylon locking nuts

SPECS:
Outside size: 7mm

This thing praises the main item here.

Suspension King Pin 2.5X31.5

This is the Traxxas (TRA) #3740 2.5x31.5mm Pins with E-clips.

FUNCTIONS:
Made from stainless-steel
This is utilized to hold the front steering block (TRAC9036 #3636)
to the castor block (TRAC9032 #3632) on the electrical
(not Nitro) Rustler
Likewise called the vertical kingpin

INCLUDES:
2 Pins (kingpins)
4 2.5mm e-clips

AXY
9/22/97

Here is a excellent thing that lots of others have actually bought at the exact same time.

Caster Blocks, For Traxxas Electric Slash, Stampede, Rustler, Ni

These are RPM 30° Front Caster Blocks for the Traxxas
Electric Stampede and Rustler.
These blocks install to the front A-arms and is what the
steering knuckles attach to.

FEATURES:
Nylon building and construction, black in color
Stamped right and delegated insure proper setup

INCLUDES:
Two RPM 30° Front Caster Blocks

REQUIRES:
Assembly between A-arms and steering knuckles