Traxxas Front Axles (2) (R & S)

This is a Set of Stock Replacement Front Axles for the Rustler and Stampede.
These are located in the front steering blocks.

FEATURES:
Steel building
Natural color

CONSISTS OF:
2 front axles

NEEDS:
Absolutely nothing. These are direct replacement parts.

SPECS:
Length: 32mm (1.26")
Diameter: 5mm

COMMENTS:
These will not work for the nitro versions. For that axle, use
    TRAC2536.

This is a superb addition to the product currently being talked about.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building
Blue rubber dirt guards

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside diameter: 3/16" (5mm)
Outside diameter: 7/16" (11mm)
Width: 5/32" (4mm)

Frequently purchased with the product that you are currently reviewing.

Hex Wheel Hub 2.5 X 12Mm Rustler / Stampede / Slash

This is a Hex Wheel Center Set for the Traxxas Rustler and
Stampede. These parts have more balanced out than
the stock hex wheel center set (TRAC6044).

FEATURES:
Gray plastic building

CONSISTS OF:
2 wheel centers
2 2.5mmX12mm axle pins

SPECIFICATIONS:
Hex size: 12mm
Width: .32" (8mm)

The listed below product likewise sets truly well with the product being talked about.

Stub Axle Pins (4)

These are replacement stub axle pins for the Nitro Buggy, Nitro Street, TRX-3,
Rad 2, TRX-1, Hawk 2, and Blue Eagle LS II. These pins slide through the axle
and hold the wheel to the axle.

INCLUDES:
4- stub axle pins

WAJ
1/30/94

This product is regularly purchased with the above discussed product.

Teflon Washers 5 X 8Mm (20)

These are Replacement Washers from Traxxas.

FEATURES:
Black plastic construction.
Used on the axles and in the transmission.

INCLUDES:
(20) Washers

SPECIFICATIONS:
Size: 5x8mm
Density: 0.5mm

Frequently purchased with the product that you are currently reviewing.

Hex Hubs & Axle Pins Slash

These are the replacement rear wheel adapters for the Hawk, Hawk 2, Bullet,
Sledgehammer, Eagle, and Blue Eagle LS. These are hex nuts that connect the
rear wheels to the axles.

INCLUDES:
2- plastic hex collars (wheel adapters)
4- stub axle pins

WAJ
1/16/93

This is a superb addition to the product currently being talked about.

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Heavy Duty Driveshaft Assembly for the Slash 4x4 from Traxxas

FEATURES:
Black plastic and steel building

CONSISTS OF:
Rear driveshaft assembly
Screw pin

NEEDS:
Installation on car

Here is another product that praises the product being talked about.

4Mm Flanged Nylock Nuts (8)

This is the Traxxas Flanged Nylon Locking Nuts.

FEATURES:
Steel serrated building

CONSISTS OF:
Eiqht 4mm flanged nylon locking nuts

SPECIFICATIONS:
Outside diameter: 7mm

This product praises the main item below.

Suspension King Pin 2.5X31.5

This is the Traxxas (TRA) #3740 2.5x31.5mm Pins with E-clips.

FEATURES:
Made from stainless steel
This is used to hold the front steering block (TRAC9036 #3636)
to the castor block (TRAC9032 #3632) on the electrical
(not Nitro) Rustler
Likewise called the vertical kingpin

CONSISTS OF:
2 Pins (kingpins)
4 2.5mm e-clips

AXY
9/22/97

Here is a wonderful product that several others have actually bought at the exact same time.

Caster Blocks, For Traxxas Electric Slash, Stampede, Rustler, Ni

These are RPM 30° Front Caster Blocks for the Traxxas
Electric Stampede and Rustler.
These obstructs install to the front A-arms and is what the
steering knuckles connect to.

FEATURES:
Nylon building, black in color
Stamped right and left to insure correct installation

CONSISTS OF:
2 RPM 30° Front Caster Blocks

NEEDS:
Assembly in between A-arms and steering knuckles