Traxxas 3.3 Engine Ips Shaft W/Pull Start

This is the Traxxas TRX 3.3 Racing Engine with Pull Starter.

FEATURES:
For use in all Traxxas TRX2.5 and TRX 3.3 equipped vehicles
Pull starter can be gotten rid of to set up the EZ Start
60% more peak power than the TRX2.5, with almost 50% more power
    under the curve for strong linear velocity
Round rear exhaust with one-piece IPS crankshaft
Composite body slide valve carburetor with high-volume air filter
Blue anodized aluminum cooling head with molded head protector

CONSISTS OF:
Traxxas TRX 3.3 Racing Engine with Pull Beginner and glow plug
One guideline manual (TRAZ5300)
One service support guide and parts lis.
One set of engine decals
One engine break-in DVD
One small bottle of air filter oil
One air filter

REQUIRES:
Vehicle fuel with 10%, 20% or 33% nitro material

SPECIFICATIONS:
Displacement: .20 cu in (3.3cc)
Practical RPM: N/A
Output: N/A
Weight: 10.9oz (305g)
Distance between mounting holes same side: 0.39" (10mm)
Distance between mounting holes opposite side: 1.2" (32mm)
Distance from center of engine to front bearing: 1.2" (32mm)
Distance/bottom of mounting flanges/top of cylinder head: 3.5" (88mm
Width of mounting flanges: 44mm

COMMENTS:
Other versions of the TRX 3.3 engine include;
    #5404 Single Shaft without Beginner, TRAG5404
    #5406 Multi-Shaft without Beginner, TRAG5406
    #5409 Multi-Shaft w/Recoil Pull Beginner, TRAG5409

Right here is an additional item that compliments the item being reviewed.



This is the DuraTrax NiMH 7.2V 3000mAh Onyx Stick Battery Load
with Requirement Connector.

FEATURES:
Perfect sport pack for automobiles, trucks and boats

CONSISTS OF:
DuraTrax NiMH 7.2V 3000mAh Onyx Stick Battery with Standard
    Port

REQUIRES:
NiMH compatible charger such as the Duratrax Onyx series

SPECIFICATIONS:
Capability: 3000mAh
Variety of Cells in Series: 6
Ranked Voltage: 7.2V
Min. Discharge Voltage: 5.4V
Maximum Recommended Charge Current: 4 amps
Discharge Lead: 14AWG 2.7" (70mm) long wire w/Standard port
Load Dimensions: 5.2 x 1.9 x 0.9" (131 x 47 x 24mm)
Weight: 13 oz (360 g)
Number of Welds per Connection: 6 area welds
Cell Size: Sub-C

This item compliments the main item here.

Cone Split Beveled

Replacement SPLIT BEVEL CONE for the Traxxas Nitro Vee Boat. This cone is
part of the engine assembly. (Image .12)

PLAN
CONSISTS OF:
1-Diagonal Cone

FUNCTIONS:
Black steel building
Diagonal cone shape with split on one side

COMMENTS:
Diagonal cone sits in front of the flywheel
7/19/94sk

Lots of others have acquired this item in addition to the item that you are currently reviewing.

T Maxx .15 To 2.5 Upgrade Kit

This is the Pro .15 to TRX 2.5 engine conversion set from Traxxas.
It allows you to mount the more recent 2.5 engine to an older T-Maxx.

FUNCTIONS:
Tuned pipe, bellcrank, & throttle servo horn made from plastic
Linkage wire made from steel

CONSISTS OF:
One Plastic Tune Pipe w/Wire Hanger (TRAG5152)
One Exhaust Header w/Screws & O-ring (TRAG5140)
One Exhaust Coupler (TRAG5246)
One Slide Carb Link Bellcrank (TRAC5167)
One Slide Carb Linkage Set (TRAC5168)
One Drill Bit for drilling Bellcrank Post mounting holes
2 Tie-Straps for mounting Exhaust Coupler
One 90-degree pressure fitting
One 3x10mm machine cap screw w/washer
One guideline sheet
One drilling template sheet

REQUIRES:
2.5 engine stock clutch system and stock engine mount

SPECIFICATIONS:
Tune Pipe Length: 101.6mm (4")
Header Pipe Outer Diameter: 13mm (.51")
Drill Bit size: 3.175mm (.125")

COMMENTS:
If EZ Start system is needed, utilize TRAP5271