Traxxas 3.3 Engine Ips Shaft W/Pull Start

This is the Traxxas TRX 3.3 Racing Engine with Pull Starter.

FEATURES:
For usage in all Traxxas TRX2.5 and TRX 3.3 equipped cars
Pull starter can be gotten rid of to install the EZ Start
60% more peak power than the TRX2.5, with nearly 50% more power
    under the curve for strong linear acceleration
Round rear exhaust with one-piece IPS crankshaft
Composite body slide valve carburetor with high-volume air filter
Blue anodized aluminum cooling head with molded head protector

CONSISTS OF:
Traxxas TRX 3.3 Racing Engine with Pull Beginner and glow plug
One instruction manual (TRAZ5300)
One service assistance guide and parts lis.
One set of engine decals
One engine burglary DVD
One small bottle of air filter oil
One air filter

REQUIRES:
Automobile fuel with 10%, 20% or 33% nitro content

SPECS:
Displacement: .20 cu in (3.3cc)
Practical RPM: N/A
Output: N/A
Weight: 10.9oz (305g)
Range between installing holes exact same side: 0.39" (10mm)
Range between installing holes opposite side: 1.2" (32mm)
Range from center of engine to front bearing: 1.2" (32mm)
Distance/bottom of installing flanges/top of cylinder head: 3.5" (88mm
Width of installing flanges: 44mm

REMARKS:
Other versions of the TRX 3.3 engine include;
    #5404 Single Shaft without Beginner, TRAG5404
    #5406 Multi-Shaft without Beginner, TRAG5406
    #5409 Multi-Shaft w/Recoil Pull Beginner, TRAG5409

Right here is one more item that compliments the item being reviewed.



This is the DuraTrax NiMH 7.2V 3000mAh Onyx Stick Battery Pack
with Requirement Connector.

FEATURES:
Suitable sport pack for vehicles, trucks and boats

CONSISTS OF:
DuraTrax NiMH 7.2V 3000mAh Onyx Stick Battery with Standard
    Adapter

REQUIRES:
NiMH suitable battery charger such as the Duratrax Onyx series

SPECS:
Capacity: 3000mAh
Variety of Cells in Series: 6
Ranked Voltage: 7.2V
Min. Release Voltage: 5.4V
Maximum Recommended Charge Current: 4 amps
Release Lead: 14AWG 2.7" (70mm) long wire w/Standard adapter
Pack Measurements: 5.2 x 1.9 x 0.9" (131 x 47 x 24mm)
Weight: 13 oz (360 g)
Number of Welds per Connection: 6 area welds
Cell Size: Sub-C

This item compliments the main item here.

Cone Split Beveled

Replacement SPLIT BEVEL CONE for the Traxxas Nitro Vee Boat. This cone is
part of the engine assembly. (Image .12)

BUNDLE
CONSISTS OF:
1-Diagonal Cone

FUNCTIONS:
Black steel construction
Diagonal cone shape with split on one side

REMARKS:
Diagonal cone sits in front of the flywheel
7/19/94sk

Many others have purchased this item along with the item that you are currently reading about.

T Maxx .15 To 2.5 Upgrade Kit

This is the Pro .15 to TRX 2.5 engine conversion set from Traxxas.
It enables you to mount the newer 2.5 engine to an older T-Maxx.

FUNCTIONS:
Tuned pipeline, bellcrank, & throttle servo horn made from plastic
Linkage wire made from steel

CONSISTS OF:
One Plastic Tune Pipe w/Wire Hanger (TRAG5152)
One Exhaust Header w/Screws & O-ring (TRAG5140)
One Exhaust Coupler (TRAG5246)
One Slide Carb Link Bellcrank (TRAC5167)
One Slide Carb Linkage Set (TRAC5168)
One Drill Bit for drilling Bellcrank Post installing holes
Two Tie-Straps for installing Exhaust Coupler
One 90-degree pressure fitting
One 3x10mm maker cap screw w/washer
One instruction sheet
One drilling template sheet

REQUIRES:
2.5 engine stock clutch system and stock engine mount

SPECS:
Tune Pipe Length: 101.6mm (4")
Header Pipe Outer Diameter: 13mm (.51")
Drill Bit size: 3.175mm (.125")

REMARKS:
If EZ Start system is required, use TRAP5271