Traxxas 3.3 Engine Ips Shaft W/Pull Start

This is the Traxxas TRX 3.3 Racing Engine with Pull Starter.

FEATURES:
For usage in all Traxxas TRX2.5 and TRX 3.3 equipped vehicles
Pull starter can be removed to set up the EZ Start
60% more peak power than the TRX2.5, with nearly 50% more power
    under the curve for strong linear velocity
Round rear exhaust with one-piece IPS crankshaft
Composite body slide valve carburetor with high-volume air filter
Blue anodized aluminum cooling head with molded head protector

CONSISTS OF:
Traxxas TRX 3.3 Racing Engine with Pull Beginner and glow plug
One direction handbook (TRAZ5300)
One service support guide and parts lis.
One set of engine decals
One engine burglary DVD
One little bottle of air filter oil
One air filter

NEEDS:
Car fuel with 10%, 20% or 33% nitro material

SPECS:
Displacement: .20 cu in (3.3cc)
Practical RPM: N/A
Output: N/A
Weight: 10.9oz (305g)
Range between installing holes exact same side: 0.39" (10mm)
Range between installing holes opposite side: 1.2" (32mm)
Range from center of engine to front bearing: 1.2" (32mm)
Distance/bottom of installing flanges/top of cylinder head: 3.5" (88mm
Width of installing flanges: 44mm

REMARKS:
Other variations of the TRX 3.3 engine consist of;
    #5404 Single Shaft without Beginner, TRAG5404
    #5406 Multi-Shaft without Beginner, TRAG5406
    #5409 Multi-Shaft w/Recoil Pull Beginner, TRAG5409

Here is one more item that praises the item being discussed.



This is the DuraTrax NiMH 7.2V 3000mAh Onyx Stick Battery Load
with Requirement Connector.

FEATURES:
Suitable sport pack for cars, trucks and boats

CONSISTS OF:
DuraTrax NiMH 7.2V 3000mAh Onyx Stick Battery with Basic
    Connector

NEEDS:
NiMH compatible battery charger such as the Duratrax Onyx series

SPECS:
Capability: 3000mAh
Number of Cells in Series: 6
Rated Voltage: 7.2V
Min. Release Voltage: 5.4V
Maximum Recommended Charge Current: 4 amps
Release Lead: 14AWG 2.7" (70mm) long wire w/Standard connector
Load Measurements: 5.2 x 1.9 x 0.9" (131 x 47 x 24mm)
Weight: 13 oz (360 g)
Number of Welds per Connection: 6 area welds
Cell Size: Sub-C

This item praises the main item below.

Cone Split Beveled

Replacement SPLIT BEVEL CONE for the Traxxas Nitro Vee Boat. This cone is
part of the engine assembly. (Image .12)

BUNDLE
CONSISTS OF:
1-Diagonal Cone

FUNCTIONS:
Black steel building and construction
Diagonal cone shape with split on one side

REMARKS:
Diagonal cone sits in front of the flywheel
7/19/94sk

Lots of others have purchased this item together with the item that you are presently reviewing.

T Maxx .15 To 2.5 Upgrade Kit

This is the Pro .15 to TRX 2.5 engine conversion set from Traxxas.
It allows you to install the more recent 2.5 engine to an older T-Maxx.

FUNCTIONS:
Tuned pipeline, bellcrank, & throttle servo horn made from plastic
Linkage wire made from steel

CONSISTS OF:
One Plastic Tune Pipeline w/Wire Hanger (TRAG5152)
One Exhaust Header w/Screws & O-ring (TRAG5140)
One Exhaust Coupler (TRAG5246)
One Slide Carbohydrate Link Bellcrank (TRAC5167)
One Slide Carbohydrate Linkage Set (TRAC5168)
One Drill Bit for drilling Bellcrank Post installing holes
Two Tie-Straps for installing Exhaust Coupler
One 90-degree pressure fitting
One 3x10mm maker cap screw w/washer
One direction sheet
One drilling template sheet

NEEDS:
2.5 engine stock clutch system and stock engine install

SPECS:
Tune Pipeline Length: 101.6mm (4")
Header Pipeline Outer Size: 13mm (.51")
Drill Bit size: 3.175mm (.125")

REMARKS:
If EZ Start system is required, use TRAP5271