Traxxas 3.3 Engine Ips Shaft W/Pull Start

This is the Traxxas TRX 3.3 Racing Engine with Pull Starter.

FEATURES:
For use in all Traxxas TRX2.5 and TRX 3.3 equipped automobiles
Pull starter can be gotten rid of to install the EZ Start
60% more peak power than the TRX2.5, with nearly 50% more power
    under the curve for strong linear acceleration
Round rear exhaust with one-piece IPS crankshaft
Composite body slide valve carburetor with high-volume air filter
Blue anodized aluminum cooling head with molded head protector

CONSISTS OF:
Traxxas TRX 3.3 Racing Engine with Pull Beginner and glow plug
One direction handbook (TRAZ5300)
One service support guide and parts lis.
One set of engine decals
One engine burglary DVD
One small bottle of air filter oil
One air filter

NEEDS:
Car fuel with 10%, 20% or 33% nitro material

SPECS:
Displacement: .20 cu in (3.3cc)
Practical RPM: N/A
Output: N/A
Weight: 10.9oz (305g)
Distance between installing holes very same side: 0.39" (10mm)
Distance between installing holes opposite side: 1.2" (32mm)
Distance from center of engine to front bearing: 1.2" (32mm)
Distance/bottom of installing flanges/top of cylinder head: 3.5" (88mm
Width of installing flanges: 44mm

COMMENTS:
Other variations of the TRX 3.3 engine include;
    #5404 Single Shaft without Beginner, TRAG5404
    #5406 Multi-Shaft without Beginner, TRAG5406
    #5409 Multi-Shaft w/Recoil Pull Beginner, TRAG5409

Here is one more thing that praises the thing being reviewed.



This is the DuraTrax NiMH 7.2V 3000mAh Onyx Stick Battery Pack
with Requirement Connector.

FEATURES:
Suitable sport pack for automobiles, trucks and boats

CONSISTS OF:
DuraTrax NiMH 7.2V 3000mAh Onyx Stick Battery with Standard
    Port

NEEDS:
NiMH suitable battery charger such as the Duratrax Onyx series

SPECS:
Capability: 3000mAh
Variety of Cells in Series: 6
Rated Voltage: 7.2V
Minutes. Release Voltage: 5.4V
Maximum Recommended Charge Current: 4 amps
Release Lead: 14AWG 2.7" (70mm) long wire w/Standard connector
Pack Measurements: 5.2 x 1.9 x 0.9" (131 x 47 x 24mm)
Weight: 13 oz (360 g)
Number of Welds per Connection: 6 spot welds
Cell Size: Sub-C

This thing praises the main item here.

Cone Split Beveled

Replacement SPLIT BEVEL CONE for the Traxxas Nitro Vee Boat. This cone is
part of the engine assembly. (Image .12)

PACKAGE
CONSISTS OF:
1-Diagonal Cone

FUNCTIONS:
Black steel building and construction
Diagonal cone shape with split on one side

COMMENTS:
Diagonal cone sits in front of the flywheel
7/19/94sk

Lots of others have actually acquired this thing along with the thing that you are presently reviewing.

T Maxx .15 To 2.5 Upgrade Kit

This is the Pro .15 to TRX 2.5 engine conversion set from Traxxas.
It enables you to mount the newer 2.5 engine to an older T-Maxx.

FUNCTIONS:
Tuned pipe, bellcrank, & throttle servo horn made from plastic
Linkage wire made from steel

CONSISTS OF:
One Plastic Tune Pipeline w/Wire Hanger (TRAG5152)
One Exhaust Header w/Screws & O-ring (TRAG5140)
One Exhaust Coupler (TRAG5246)
One Slide Carbohydrate Link Bellcrank (TRAC5167)
One Slide Carbohydrate Linkage Set (TRAC5168)
One Drill Bit for drilling Bellcrank Post installing holes
2 Tie-Straps for installing Exhaust Coupler
One 90-degree pressure fitting
One 3x10mm machine cap screw w/washer
One direction sheet
One drilling design template sheet

NEEDS:
2.5 engine stock clutch system and stock engine mount

SPECS:
Tune Pipeline Length: 101.6mm (4")
Header Pipeline Outer Size: 13mm (.51")
Drill Bit size: 3.175mm (.125")

COMMENTS:
If EZ Start system is needed, utilize TRAP5271