Traxxas 3.3 Engine Ips Shaft W/Pull Start

This is the Traxxas TRX 3.3 Racing Engine with Pull Starter.

FEATURES:
For usage in all Traxxas TRX2.5 and TRX 3.3 equipped vehicles
Pull starter can be removed to install the EZ Start
60% more peak power than the TRX2.5, with almost 50% more power
    under the curve for strong linear acceleration
Round rear exhaust with one-piece IPS crankshaft
Composite body slide valve carburetor with high-volume air filter
Blue anodized aluminum cooling head with molded head protector

INCLUDES:
Traxxas TRX 3.3 Racing Engine with Pull Beginner and glow plug
One guideline manual (TRAZ5300)
One service support guide and parts lis.
One set of engine decals
One engine burglary DVD
One small bottle of air filter oil
One air filter

NEEDS:
Automobile fuel with 10%, 20% or 33% nitro content

SPECIFICATIONS:
Displacement: .20 cu in (3.3cc)
Practical RPM: N/A
Output: N/A
Weight: 10.9oz (305g)
Range in between installing holes exact same side: 0.39" (10mm)
Range in between installing holes opposite side: 1.2" (32mm)
Range from center of engine to front bearing: 1.2" (32mm)
Distance/bottom of installing flanges/top of cylinder head: 3.5" (88mm
Width of installing flanges: 44mm

REMARKS:
Other versions of the TRX 3.3 engine consist of;
    #5404 Single Shaft without Beginner, TRAG5404
    #5406 Multi-Shaft without Beginner, TRAG5406
    #5409 Multi-Shaft w/Recoil Pull Beginner, TRAG5409

Right here is another thing that compliments the thing being gone over.



This is the DuraTrax NiMH 7.2V 3000mAh Onyx Stick Battery Load
with Standard Connector.

FEATURES:
Perfect sport pack for vehicles, trucks and boats

INCLUDES:
DuraTrax NiMH 7.2V 3000mAh Onyx Stick Battery with Standard
    Connector

NEEDS:
NiMH suitable battery charger such as the Duratrax Onyx series

SPECIFICATIONS:
Capacity: 3000mAh
Variety of Cells in Series: 6
Rated Voltage: 7.2V
Minutes. Release Voltage: 5.4V
Optimum Recommended Charge Current: 4 amps
Release Lead: 14AWG 2.7" (70mm) long wire w/Standard connector
Load Dimensions: 5.2 x 1.9 x 0.9" (131 x 47 x 24mm)
Weight: 13 oz (360 g)
Number of Welds per Connection: 6 area welds
Cell Size: Sub-C

This thing compliments the main item here.

Cone Split Beveled

Replacement SPLIT BEVEL CONE for the Traxxas Nitro Vee Boat. This cone is
part of the engine assembly. (Image .12)

PLAN
INCLUDES:
1-Diagonal Cone

FEATURES:
Black steel building and construction
Diagonal cone shape with split on one side

REMARKS:
Diagonal cone sits in front of the flywheel
7/19/94sk

Lots of others have actually bought this thing along with the thing that you are presently checking out.

T Maxx .15 To 2.5 Upgrade Kit

This is the Pro .15 to TRX 2.5 engine conversion set from Traxxas.
It allows you to mount the more recent 2.5 engine to an older T-Maxx.

FEATURES:
Tuned pipe, bellcrank, & throttle servo horn made from plastic
Linkage wire made from steel

INCLUDES:
One Plastic Tune Pipeline w/Wire Hanger (TRAG5152)
One Exhaust Header w/Screws & O-ring (TRAG5140)
One Exhaust Coupler (TRAG5246)
One Slide Carb Link Bellcrank (TRAC5167)
One Slide Carb Linkage Set (TRAC5168)
One Drill Bit for drilling Bellcrank Post installing holes
Two Tie-Straps for installing Exhaust Coupler
One 90-degree pressure fitting
One 3x10mm device cap screw w/washer
One guideline sheet
One drilling design template sheet

NEEDS:
2.5 engine stock clutch system and stock engine mount

SPECIFICATIONS:
Tune Pipeline Length: 101.6mm (4")
Header Pipeline Outer Size: 13mm (.51")
Drill Bit size: 3.175mm (.125")

REMARKS:
If EZ Start system is needed, use TRAP5271