Traxxas 3.3 Engine Ips Shaft W/Pull Start

This is the Traxxas TRX 3.3 Racing Engine with Pull Starter.

FEATURES:
For usage in all Traxxas TRX2.5 and TRX 3.3 equipped cars
Pull starter can be gotten rid of to install the EZ Start
60% more peak power than the TRX2.5, with almost 50% more power
    under the curve for strong linear acceleration
Round rear exhaust with one-piece IPS crankshaft
Composite body slide valve carburetor with high-volume air filter
Blue anodized aluminum cooling head with molded head protector

CONSISTS OF:
Traxxas TRX 3.3 Racing Engine with Pull Beginner and radiance plug
One guideline manual (TRAZ5300)
One service assistance guide and parts lis.
One set of engine decals
One engine break-in DVD
One small bottle of air filter oil
One air filter

NEEDS:
Vehicle fuel with 10%, 20% or 33% nitro content

SPECIFICATIONS:
Displacement: .20 cu in (3.3cc)
Practical RPM: N/A
Output: N/A
Weight: 10.9oz (305g)
Distance between mounting holes very same side: 0.39" (10mm)
Distance between mounting holes opposite side: 1.2" (32mm)
Distance from center of engine to front bearing: 1.2" (32mm)
Distance/bottom of mounting flanges/top of cylinder head: 3.5" (88mm
Width of mounting flanges: 44mm

REMARKS:
Other versions of the TRX 3.3 engine consist of;
    #5404 Single Shaft without Beginner, TRAG5404
    #5406 Multi-Shaft without Beginner, TRAG5406
    #5409 Multi-Shaft w/Recoil Pull Beginner, TRAG5409

Here is an additional product that compliments the product being discussed.



This is the DuraTrax NiMH 7.2V 3000mAh Onyx Stick Battery Pack
with Standard Connector.

FEATURES:
Ideal sport pack for cars, trucks and boats

CONSISTS OF:
DuraTrax NiMH 7.2V 3000mAh Onyx Stick Battery with Standard
    Connector

NEEDS:
NiMH suitable charger such as the Duratrax Onyx series

SPECIFICATIONS:
Capacity: 3000mAh
Variety of Cells in Series: 6
Rated Voltage: 7.2V
Min. Discharge Voltage: 5.4V
Optimum Recommended Charge Current: 4 amps
Discharge Lead: 14AWG 2.7" (70mm) long wire w/Standard port
Pack Measurements: 5.2 x 1.9 x 0.9" (131 x 47 x 24mm)
Weight: 13 oz (360 g)
Number of Welds per Connection: 6 spot welds
Cell Size: Sub-C

This product compliments the main item here.

Cone Split Beveled

Replacement SPLIT BEVEL CONE for the Traxxas Nitro Vee Boat. This cone is
part of the engine assembly. (Image .12)

PLAN
CONSISTS OF:
1-Diagonal Cone

FUNCTIONS:
Black steel building and construction
Diagonal cone shape with split on one side

REMARKS:
Diagonal cone sits in front of the flywheel
7/19/94sk

Numerous others have actually purchased this product in addition to the product that you are currently checking out.

T Maxx .15 To 2.5 Upgrade Kit

This is the Pro .15 to TRX 2.5 engine conversion set from Traxxas.
It permits you to mount the newer 2.5 engine to an older T-Maxx.

FUNCTIONS:
Tuned pipe, bellcrank, & throttle servo horn made of plastic
Linkage wire made of steel

CONSISTS OF:
One Plastic Tune Pipeline w/Wire Hanger (TRAG5152)
One Exhaust Header w/Screws & O-ring (TRAG5140)
One Exhaust Coupler (TRAG5246)
One Slide Carb Link Bellcrank (TRAC5167)
One Slide Carb Linkage Set (TRAC5168)
One Drill Bit for drilling Bellcrank Post mounting holes
Two Tie-Straps for mounting Exhaust Coupler
One 90-degree pressure fitting
One 3x10mm device cap screw w/washer
One guideline sheet
One drilling design template sheet

NEEDS:
2.5 engine stock clutch system and stock engine mount

SPECIFICATIONS:
Tune Pipeline Length: 101.6mm (4")
Header Pipeline Outer Diameter: 13mm (.51")
Drill Bit size: 3.175mm (.125")

REMARKS:
If EZ Start system is needed, use TRAP5271