Traxxas 3.3 Engine Ips Shaft W/Pull Start

This is the Traxxas TRX 3.3 Racing Engine with Pull Starter.

FEATURES:
For usage in all Traxxas TRX2.5 and TRX 3.3 equipped automobiles
Pull starter can be gotten rid of to install the EZ Start
60% more peak power than the TRX2.5, with almost 50% more power
    under the curve for strong linear acceleration
Round rear exhaust with one-piece IPS crankshaft
Composite body slide valve carburetor with high-volume air filter
Blue anodized aluminum cooling head with molded head protector

CONSISTS OF:
Traxxas TRX 3.3 Racing Engine with Pull Starter and radiance plug
One instruction handbook (TRAZ5300)
One service assistance guide and parts lis.
One set of engine decals
One engine burglary DVD
One little bottle of air filter oil
One air filter

REQUIRES:
Automobile fuel with 10%, 20% or 33% nitro material

SPECS:
Displacement: .20 cu in (3.3cc)
Practical RPM: N/A
Output: N/A
Weight: 10.9oz (305g)
Range between mounting holes exact same side: 0.39" (10mm)
Range between mounting holes opposite side: 1.2" (32mm)
Range from center of engine to front bearing: 1.2" (32mm)
Distance/bottom of mounting flanges/top of cylinder head: 3.5" (88mm
Width of mounting flanges: 44mm

REMARKS:
Other variations of the TRX 3.3 engine include;
    #5404 Single Shaft without Starter, TRAG5404
    #5406 Multi-Shaft without Starter, TRAG5406
    #5409 Multi-Shaft w/Recoil Pull Starter, TRAG5409

Right here is another item that praises the item being discussed.



This is the DuraTrax NiMH 7.2V 3000mAh Onyx Stick Battery Load
with Standard Connector.

FEATURES:
Ideal sport pack for vehicles, trucks and boats

CONSISTS OF:
DuraTrax NiMH 7.2V 3000mAh Onyx Stick Battery with Conventional
    Port

REQUIRES:
NiMH compatible charger such as the Duratrax Onyx series

SPECS:
Capacity: 3000mAh
Variety of Cells in Series: 6
Ranked Voltage: 7.2V
Min. Release Voltage: 5.4V
Maximum Recommended Charge Current: 4 amps
Release Lead: 14AWG 2.7" (70mm) long wire w/Standard port
Load Dimensions: 5.2 x 1.9 x 0.9" (131 x 47 x 24mm)
Weight: 13 oz (360 g)
Number of Welds per Connection: 6 area welds
Cell Size: Sub-C

This item praises the main item here.

Cone Split Beveled

Replacement SPLIT BEVEL CONE for the Traxxas Nitro Vee Boat. This cone is
part of the engine assembly. (Image .12)

PACKAGE
CONSISTS OF:
1-Diagonal Cone

FUNCTIONS:
Black steel building and construction
Diagonal cone shape with split on one side

REMARKS:
Diagonal cone sits in front of the flywheel
7/19/94sk

Several others have actually acquired this item in addition to the item that you are presently reviewing.

T Maxx .15 To 2.5 Upgrade Kit

This is the Pro .15 to TRX 2.5 engine conversion set from Traxxas.
It enables you to mount the newer 2.5 engine to an older T-Maxx.

FUNCTIONS:
Tuned pipe, bellcrank, & throttle servo horn made of plastic
Linkage wire made of steel

CONSISTS OF:
One Plastic Tune Pipe w/Wire Hanger (TRAG5152)
One Exhaust Header w/Screws & O-ring (TRAG5140)
One Exhaust Coupler (TRAG5246)
One Slide Carbohydrate Link Bellcrank (TRAC5167)
One Slide Carbohydrate Linkage Set (TRAC5168)
One Drill Bit for drilling Bellcrank Post mounting holes
2 Tie-Straps for mounting Exhaust Coupler
One 90-degree pressure fitting
One 3x10mm machine cap screw w/washer
One instruction sheet
One drilling template sheet

REQUIRES:
2.5 engine stock clutch system and stock engine mount

SPECS:
Tune Pipe Length: 101.6mm (4")
Header Pipe Outer Diameter: 13mm (.51")
Drill Bit size: 3.175mm (.125")

REMARKS:
If EZ Start system is needed, use TRAP5271