Traxxas Driveshaft, Center, Aluminum (

This is the Aluminum Center Driveshaft for the Traxxas Slash 4x4 Vehicles.

FEATURES:
Hollow aluminum building and construction
Anodized blue in color

INCLUDES:
One Aluminum Center Driveshaft

REQUIRES:
Setup on the automobile

SPECS:
Length: 215mm (8.5")
Diameter: 8.3mm (0.33")

Frequently purchased with the thing that you are presently checking out.

Hold Down, Tall Battery Slash

This is the Hold Down Battery Set for the 2WD Traxxas Slash.
**Will not deal with the Traxxas Slash 4x4.**

FEATURES:
Black nylon building and construction

INCLUDES:
One Battery Hold Down
One Retainer Hold Down
One Battery Post
One Foam Spacer
One Angled Body Clip

REQUIRES:
Setup on the chassis

This thing praises the main item here.

Cover, Center Driveshaft (Clea

This is the Center Driveshaft Cover for the Traxxas Slash 4x4 Vehicles.

FEATURES:
Clear nylon building and construction

INCLUDES:
One Center Driveshaft Cover

REQUIRES:
Setup over driveshaft

SPECS:
Length: 210mm (8.3")
Width: 15mm (0.59")

This is a great enhancement to the thing presently being gone over.

54T 0.8 P Spur Gear

This is the 54 Tooth Spur Gear
for the Traxxas Nitro Jato Stadium Truck.

FEATURES:
Nylon building and construction
Black in color
.8 Module pitch

INCLUDES:
One 54T 0.8 Pitch Spur Gear

REQUIRES:
Assembly onto automobile

Want an additional terrific thing to compliment the above stated thing?

Motor Heat Sink

This is the initial replacement motor heatsink for the Traxxas Bad guy IV.
AXY
4/8/92

This thing is frequently purchased with the above stated thing.

Drive Hub, Center, Rear (1)/ F

This is the Front and Back Center Drive Center Set for use on the
Traxxas Slash 4x4 Vehicles.

FEATURES:
Nylon and steel building and construction

INCLUDES:
One Front Center Drive Center
One Back Center Drive Center
One Screw Pin

REQUIRES:
Setup in drive assembly

Want an additional terrific thing to compliment the above stated thing?

Bumper, Front/ Bumper Mount, F

This is the Front Bumper and Mount for the Traxxas Slash 4x4.

FEATURES:
Hardened plastic building and construction
Black in color

INCLUDES:
One Front bumper
One Front bumper install

REQUIRES:
Setup on chassis

This is a great enhancement to the thing presently being gone over.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building and construction
Blue rubber dirt guards

INCLUDES:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside size: 3/16" (5mm)
Outside size: 7/16" (11mm)
Width: 5/32" (4mm)

Want an additional terrific thing to compliment the above stated thing?

10 X 15 X 4Mm Ball Bearing (2) Blue Rubber Sheild Revo

This is a set of 10x15mm Ball Bearings for use on the Traxxas Revo.

FEATURES:
Steel Building
Shielded with blue rubber seals

INCLUDES:
Two Ball Bearings

REQUIRES:
Assembly to automobile

SPECS:
Inner Diameter: 10mm
Outer Diameter: 15mm
Side Thickness: 4mm

COMMENTS:
These bearings are utilized to support the Primary Clutch (one required).

This thing praises the main item here.

Traxxas Slash 4X4 Rear Bumper-Blue

This is the optional RPM Back Bumper for use on the Traxxas Slash 4x4.
Will NOT deal with the Slash 2WD.

FEATURES:
Nylon building and construction
Blue in color

INCLUDES:
One Left Side Bumper Assistance
One Right Side Bumper Assistance
One Rear Bumper
8 3x16mm Buttonhead Screws
One Upper Bumper Mount
One Lower Bumper Mount

REQUIRES:
Setup on the automobile

COMMENTS:
Likewise offered in: Black (RPMC0122)
Chrome (RPMC0123)