Traxxas Driveshaft, Center, Aluminum (

This is the Aluminum Center Driveshaft for the Traxxas Slash 4x4 Vehicles.

FEATURES:
Hollow aluminum construction
Anodized blue in color

CONSISTS OF:
One Aluminum Center Driveshaft

NEEDS:
Installation on the vehicle

SPECIFICATIONS:
Length: 215mm (8.5")
Size: 8.3mm (0.33")

Regularly gotten with the thing that you are currently reading about.

Hold Down, Tall Battery Slash

This is the Hold Down Battery Set for the 2WD Traxxas Slash.
**Will not work with the Traxxas Slash 4x4.**

FUNCTIONS:
Black nylon construction

CONSISTS OF:
One Battery Hold Down
One Retainer Hold Down
One Battery Post
One Foam Spacer
One Angled Body Clip

NEEDS:
Installation on the chassis

This thing praises the main item right here.

Cover, Center Driveshaft (Clea

This is the Center Driveshaft Cover for the Traxxas Slash 4x4 Vehicles.

FEATURES:
Clear nylon construction

CONSISTS OF:
One Center Driveshaft Cover

NEEDS:
Installation over driveshaft

SPECIFICATIONS:
Length: 210mm (8.3")
Width: 15mm (0.59")

This is a amazing addition to the thing currently being talked about.

54T 0.8 P Spur Gear

This is the 54 Tooth Spur Gear
for the Traxxas Nitro Jato Arena Truck.

FEATURES:
Nylon construction
Black in color
.8 Module pitch

CONSISTS OF:
One 54T 0.8 Pitch Spur Gear

NEEDS:
Assembly onto vehicle

Want an additional great thing to enhance the above discussed thing?

Motor Heat Sink

This is the original replacement motor heatsink for the Traxxas Bad guy IV.
AXY
4/8/92

This thing is frequently gotten with the above discussed thing.

Drive Hub, Center, Rear (1)/ F

This is the Front and Back Center Drive Hub Set for usage on the
Traxxas Slash 4x4 Vehicles.

FEATURES:
Nylon and steel construction

CONSISTS OF:
One Front Center Drive Hub
One Back Center Drive Hub
One Screw Pin

NEEDS:
Installation in drive assembly

Want an additional great thing to enhance the above discussed thing?

Bumper, Front/ Bumper Mount, F

This is the Front Bumper and Mount for the Traxxas Slash 4x4.

FUNCTIONS:
Hardened plastic construction
Black in color

CONSISTS OF:
One Front bumper
One Front bumper install

NEEDS:
Installation on chassis

This is a amazing addition to the thing currently being talked about.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing construction
Blue rubber dirt guards

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside size: 3/16" (5mm)
Outside size: 7/16" (11mm)
Width: 5/32" (4mm)

Want an additional great thing to enhance the above discussed thing?

10 X 15 X 4Mm Ball Bearing (2) Blue Rubber Sheild Revo

This is a set of 10x15mm Ball Bearings for usage on the Traxxas Revo.

FEATURES:
Steel Building and construction
Protected with blue rubber seals

CONSISTS OF:
Two Ball Bearings

NEEDS:
Assembly to vehicle

SPECIFICATIONS:
Inner Size: 10mm
Outer Size: 15mm
Side Thickness: 4mm

COMMENTS:
These bearings are used to support the Primary Clutch (one required).

This thing praises the main item right here.

Traxxas Slash 4X4 Rear Bumper-Blue

This is the optional RPM Back Bumper for usage on the Traxxas Slash 4x4.
Will NOT work with the Slash 2WD.

FUNCTIONS:
Nylon construction
Blue in color

CONSISTS OF:
One Left Side Bumper Support
One Right Side Bumper Support
One Rear Bumper
Eight 3x16mm Buttonhead Screws
One Upper Bumper Mount
One Lower Bumper Mount

NEEDS:
Installation on the vehicle

COMMENTS:
Also offered in: Black (RPMC0122)
Chrome (RPMC0123)