Traxxas Driveshaft, Center, Aluminum (

This is the Aluminum Center Driveshaft for the Traxxas Slash 4x4 Vehicles.

FEATURES:
Hollow aluminum building and construction
Anodized blue in color

CONSISTS OF:
One Aluminum Center Driveshaft

NEEDS:
Installation on the vehicle

SPECS:
Length: 215mm (8.5")
Diameter: 8.3mm (0.33")

Often bought with the thing that you are currently reviewing.

Hold Down, Tall Battery Slash

This is the Hold Down Battery Set for the 2WD Traxxas Slash.
**Will not work with the Traxxas Slash 4x4.**

FEATURES:
Black nylon building and construction

CONSISTS OF:
One Battery Hold Down
One Retainer Hold Down
One Battery Post
One Foam Spacer
One Angled Body Clip

NEEDS:
Installation on the chassis

This thing praises the main item below.

Cover, Center Driveshaft (Clea

This is the Center Driveshaft Cover for the Traxxas Slash 4x4 Vehicles.

FEATURES:
Clear nylon building and construction

CONSISTS OF:
One Center Driveshaft Cover

NEEDS:
Installation over driveshaft

SPECS:
Length: 210mm (8.3")
Width: 15mm (0.59")

This is a superb enhancement to the thing currently being gone over.

54T 0.8 P Spur Gear

This is the 54 Tooth Spur Gear
for the Traxxas Nitro Jato Arena Truck.

FEATURES:
Nylon building and construction
Black in color
.8 Module pitch

CONSISTS OF:
One 54T 0.8 Pitch Spur Gear

NEEDS:
Assembly onto vehicle

Want another great thing to match the above discussed thing?

Motor Heat Sink

This is the original replacement motor heatsink for the Traxxas Bad guy IV.
AXY
4/8/92

This thing is frequently bought with the above discussed thing.

Drive Hub, Center, Rear (1)/ F

This is the Front and Rear Center Drive Hub Set for use on the
Traxxas Slash 4x4 Vehicles.

FEATURES:
Nylon and steel building and construction

CONSISTS OF:
One Front Center Drive Hub
One Rear Center Drive Hub
One Screw Pin

NEEDS:
Installation in drive assembly

Want another great thing to match the above discussed thing?

Bumper, Front/ Bumper Mount, F

This is the Front Bumper and Mount for the Traxxas Slash 4x4.

FEATURES:
Hardened plastic building and construction
Black in color

CONSISTS OF:
One Front bumper
One Front bumper mount

NEEDS:
Installation on chassis

This is a superb enhancement to the thing currently being gone over.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building and construction
Blue rubber dirt shields

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside diameter: 3/16" (5mm)
Outside diameter: 7/16" (11mm)
Width: 5/32" (4mm)

Want another great thing to match the above discussed thing?

10 X 15 X 4Mm Ball Bearing (2) Blue Rubber Sheild Revo

This is a set of 10x15mm Ball Bearings for use on the Traxxas Revo.

FEATURES:
Steel Building
Shielded with blue rubber seals

CONSISTS OF:
2 Ball Bearings

NEEDS:
Assembly to vehicle

SPECS:
Inner Diameter: 10mm
External Diameter: 15mm
Side Density: 4mm

COMMENTS:
These bearings are utilized to support the Primary Clutch (one needed).

This thing praises the main item below.

Traxxas Slash 4X4 Rear Bumper-Blue

This is the optional RPM Rear Bumper for use on the Traxxas Slash 4x4.
Will NOT work with the Slash 2WD.

FEATURES:
Nylon building and construction
Blue in color

CONSISTS OF:
One Left Side Bumper Assistance
One Right Side Bumper Assistance
One Rear Bumper
8 3x16mm Buttonhead Screws
One Upper Bumper Mount
One Lower Bumper Mount

NEEDS:
Installation on the vehicle

COMMENTS:
Likewise available in: Black (RPMC0122)
Chrome (RPMC0123)