Traxxas Driveshaft, Center, Aluminum (

This is the Aluminum Center Driveshaft for the Traxxas Slash 4x4 Vehicles.

FEATURES:
Hollow aluminum construction
Anodized blue in color

CONSISTS OF:
One Aluminum Center Driveshaft

NEEDS:
Setup on the vehicle

SPECS:
Length: 215mm (8.5")
Diameter: 8.3mm (0.33")

Regularly gotten with the item that you are currently reviewing.

Hold Down, Tall Battery Slash

This is the Hold Down Battery Set for the 2WD Traxxas Slash.
**Will not work with the Traxxas Slash 4x4.**

FEATURES:
Black nylon construction

CONSISTS OF:
One Battery Hold Down
One Retainer Hold Down
One Battery Post
One Foam Spacer
One Angled Body Clip

NEEDS:
Setup on the chassis

This item praises the main item below.

Cover, Center Driveshaft (Clea

This is the Center Driveshaft Cover for the Traxxas Slash 4x4 Vehicles.

FEATURES:
Clear nylon construction

CONSISTS OF:
One Center Driveshaft Cover

NEEDS:
Setup over driveshaft

SPECS:
Length: 210mm (8.3")
Width: 15mm (0.59")

This is a fantastic enhancement to the item currently being gone over.

54T 0.8 P Spur Gear

This is the 54 Tooth Spur Gear
for the Traxxas Nitro Jato Arena Truck.

FEATURES:
Nylon construction
Black in color
.8 Module pitch

CONSISTS OF:
One 54T 0.8 Pitch Spur Gear

NEEDS:
Assembly onto vehicle

Want another terrific item to enhance the above discussed item?

Motor Heat Sink

This is the original replacement motor heatsink for the Traxxas Villain IV.
AXY
4/8/92

This item is frequently gotten with the above discussed item.

Drive Hub, Center, Rear (1)/ F

This is the Front and Rear Center Drive Center Set for use on the
Traxxas Slash 4x4 Vehicles.

FEATURES:
Nylon and steel construction

CONSISTS OF:
One Front Center Drive Center
One Rear Center Drive Center
One Screw Pin

NEEDS:
Setup in drive assembly

Want another terrific item to enhance the above discussed item?

Bumper, Front/ Bumper Mount, F

This is the Front Bumper and Mount for the Traxxas Slash 4x4.

FEATURES:
Hardened plastic construction
Black in color

CONSISTS OF:
One Front bumper
One Front bumper install

NEEDS:
Setup on chassis

This is a fantastic enhancement to the item currently being gone over.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing construction
Blue rubber dirt guards

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside diameter: 3/16" (5mm)
Outdoors diameter: 7/16" (11mm)
Width: 5/32" (4mm)

Want another terrific item to enhance the above discussed item?

10 X 15 X 4Mm Ball Bearing (2) Blue Rubber Sheild Revo

This is a set of 10x15mm Ball Bearings for use on the Traxxas Revo.

FEATURES:
Steel Construction
Protected with blue rubber seals

CONSISTS OF:
2 Ball Bearings

NEEDS:
Assembly to vehicle

SPECS:
Inner Diameter: 10mm
External Diameter: 15mm
Side Thickness: 4mm

COMMENTS:
These bearings are utilized to support the Primary Clutch (one needed).

This item praises the main item below.

Traxxas Slash 4X4 Rear Bumper-Blue

This is the optional RPM Rear Bumper for use on the Traxxas Slash 4x4.
Will NOT work with the Slash 2WD.

FEATURES:
Nylon construction
Blue in color

CONSISTS OF:
One Left Side Bumper Assistance
One Right Side Bumper Assistance
One Rear Bumper
8 3x16mm Buttonhead Screws
One Upper Bumper Mount
One Lower Bumper Mount

NEEDS:
Setup on the vehicle

COMMENTS:
Likewise available in: Black (RPMC0122)
Chrome (RPMC0123)