Traxxas Driveshaft Assembly (1)

This is the Driveshaft Assembly for the Traxxas Revo 3.3.
and the T-Maxx 3.3.

FEATURES:
Totally put together
Plastic telescoping driveshaft with steel universals
Blue rubber boot shields telescoping areas from dirt
Attaches to the differential with one screw pin
Functions on the front or rear, right or left of vehicle

CONSISTS OF:
#5458X Yoke, TRAC9798
#5145 Screw Pin, TRAC5145
#5450 Halfshaft, TRAC7450
#5452 U Joint, TRAC7452
#5459 Rubber Boot, TRAC7459
Guideline sheet

REQUIRES:
Installing on chassis

This thing praises the main item here.

54T 0.8 P Spur Gear

This is the 54 Tooth Spur Gear
for the Traxxas Nitro Jato Arena Truck.

FEATURES:
Nylon building and construction
Black in color
.8 Module pitch

CONSISTS OF:
One 54T 0.8 Pitch Spur Gear

REQUIRES:
Assembly onto vehicle

Many others have purchased this thing along with the thing that you are presently reviewing.

12 X 18 X 4Mm Ball Bearing (2) Blue Rubber Sheild Revo

    These are the replacement Wheel Center Ball Bearings for
the Traxxas Nitro Revo Beast Truck.

FEATURES:
Stainless-steel Construction
Blue Rubber Sealed

CONSISTS OF:
2 12mm x 18mm Blue Sealed Stainless Wheel Center Bearings

REQUIRES:
Assembly onto Car

SPECS:
Outer Size: 18mm (0.70")
Inner Size: 12mm (0.47")
Thickness: 4mm (0.15")

REMARKS:
These are for the Inside of the Wheel Hubs, the Truck Needs
Four Total of these Bearings.

The below thing also pairs really well with the thing being gone over.

Half Shaft Set Left Or Right Revo

This is a replacement Half Shaft Set for the Traxxas Revo Truck.
This package consists of a part of the telescoping drive shafts.

FEATURES:
Black plastic building and construction
Blue rubber shaft boots

CONSISTS OF:
2 half shaft assemblies

REQUIRES:
Absolutely nothing. These are direct replacement parts.

SPECS:
Length: 120mm (4.7")

Often purchased with the thing that you are presently reviewing.

Bbs Blue Rubber Sealed 6 X 13M

This is a set of Traxxas 6x13x5mm Ball Bearings
for usage on the E-Revo

FEATURES:
Stainless-steel bearing building and construction
Blue rubber dirt shields

CONSISTS OF:
(2) 6x13x5mm ball bearings Part #5180

SPECS:
Inside diameter: 6mm (0.24")
Outside diameter: 13mm (0.51")
Width: 5mm (0.20")

Get this thing to improve the one you are reading around.

Axle Carriers Left & Right (1 Ea) Revo

This is the set of Axle Carriers and Steering Blocks for the Traxxas Revo.
The axle providers and steering blocks support the stub axles and bolt
    to the upper and lower suspension arms at each wheel.

FEATURES:
Changes damaged axle providers and steering blocks.
Constructed of black plastic.

INCLUDES:
One set of axle providers and steering blocks for the Traxxas Revo.

REQUIRES:
Bolting to each suspension arm, installing two 12x18mm ball
    bearings, stub axles, and pillow balls.

Here is a terrific thing that lots of others have purchased the same time.

Axle Carriers Use Larger 6 X 1

These are the Optional Axle Carriers L & R for
usage on the Traxxas Revo series.

FEATURES:
Nylon Construction
Black in Color
Enables for Oversized Bearing utilize

CONSISTS OF:
One Left Axle Provider
One Right Axle Provider
Four Dust Boot Retainers
2 Bearing Spacers

REQUIRES:
Setup

Often purchased with the thing that you are presently reviewing.

E-Revo Body Prographix

    This is a PROGRAPHIX Body for the Traxxas E-Revo
Covers and Safeguards the Vehicle.

FEATURES:
Lexan building and construction
Pre-painted graphics
Body mount holes pre-drilled
Pre-cut
Protective film covers outside of body after finish and is gotten rid of
    after conclusion of paint task

CONSISTS OF:
One painted graphics E-Revo Body
One decal set

REQUIRES:
Lexan safe spray or brush-on paint
Traxxas E-Revo

SPECS:
Length: 500mm (19.7")
Width: 185mm (7.28")
Height: 125mm (4.92")

REMARK:
Graphics are pre-painted. Needs paint and final
decal application.