Traxxas Driveshaft Assembly (1)

This is the Driveshaft Assembly for the Traxxas Revo 3.3.
and the T-Maxx 3.3.

FEATURES:
Totally assembled
Plastic telescoping driveshaft with steel universals
Blue rubber boot guards telescoping sections from dirt
Attaches to the differential with one screw pin
Works on the front or back, right or left of car

INCLUDES:
#5458X Yoke, TRAC9798
#5145 Screw Pin, TRAC5145
#5450 Halfshaft, TRAC7450
#5452 U Joint, TRAC7452
#5459 Rubber Boot, TRAC7459
Direction sheet

NEEDS:
Installing on chassis

This item compliments the main item below.

54T 0.8 P Spur Gear

This is the 54 Tooth Spur Gear
for the Traxxas Nitro Jato Arena Truck.

FEATURES:
Nylon construction
Black in color
.8 Module pitch

INCLUDES:
One 54T 0.8 Pitch Spur Gear

NEEDS:
Assembly onto car

Lots of others have purchased this item along with the item that you are presently reading about.

12 X 18 X 4Mm Ball Bearing (2) Blue Rubber Sheild Revo

    These are the replacement Wheel Center Ball Bearings for
the Traxxas Nitro Revo Monster Truck.

FEATURES:
Stainless-steel Building
Blue Rubber Sealed

INCLUDES:
Two 12mm x 18mm Blue Sealed Stainless Wheel Center Bearings

NEEDS:
Assembly onto Car

SPECIFICATIONS:
Outer Diameter: 18mm (0.70")
Inner Diameter: 12mm (0.47")
Density: 4mm (0.15")

COMMENTS:
These are for the Inside of the Wheel Hubs, the Truck Needs
Four Overall of these Bearings.

The below item also sets actually well with the item being discussed.

Half Shaft Set Left Or Right Revo

This is a replacement Half Shaft Set for the Traxxas Revo Truck.
This plan contains a portion of the telescoping drive shafts.

FEATURES:
Black plastic construction
Blue rubber shaft boots

INCLUDES:
Two half shaft assemblies

NEEDS:
Nothing. These are direct replacement parts.

SPECS:
Length: 120mm (4.7")

Frequently purchased with the item that you are presently reading about.

Bbs Blue Rubber Sealed 6 X 13M

This is a set of Traxxas 6x13x5mm Ball Bearings
for usage on the E-Revo

FEATURES:
Stainless-steel bearing construction
Blue rubber dirt guards

INCLUDES:
(2) 6x13x5mm ball bearings Part #5180

SPECIFICATIONS:
Inside size: 6mm (0.24")
Outdoors size: 13mm (0.51")
Width: 5mm (0.20")

Get this item to boost the one you are reading around.

Axle Carriers Left & Right (1 Ea) Revo

This is the set of Axle Carriers and Steering Blocks for the Traxxas Revo.
The axle carriers and guiding blocks support the stub axles and bolt
    to the upper and lower suspension arms at each wheel.

FEATURES:
Changes broken axle carriers and guiding blocks.
Constructed of black plastic.

INCLUDES:
One set of axle carriers and guiding blocks for the Traxxas Revo.

REQUIRES:
Bolting to each suspension arm, installing 2 12x18mm ball
    bearings, stub axles, and pillow balls.

Here is a great item that lots of others have bought at the exact same time.

Axle Carriers Use Larger 6 X 1

These are the Optional Axle Carriers L & R for
usage on the Traxxas Revo series.

FEATURES:
Nylon Building
Black in Color
Enables for Oversized Bearing use

INCLUDES:
One Left Axle Carrier
One Right Axle Carrier
Four Dust Boot Retainers
Two Bearing Spacers

NEEDS:
Setup

Frequently purchased with the item that you are presently reading about.

E-Revo Body Prographix

    This is a PROGRAPHIX Body for the Traxxas E-Revo
Covers and Protects the Vehicle.

FEATURES:
Lexan construction
Pre-painted graphics
Body install holes pre-drilled
Pre-cut
Protective film covers beyond body after surface and is removed
    after conclusion of paint task

INCLUDES:
One painted graphics E-Revo Body
One decal set

NEEDS:
Lexan safe spray or brush-on paint
Traxxas E-Revo

SPECIFICATIONS:
Length: 500mm (19.7")
Width: 185mm (7.28")
Height: 125mm (4.92")

COMMENT:
Graphics are pre-painted. Needs paint and final
decal application.