Traxxas Driveshaft Assembly (1)

This is the Driveshaft Assembly for the Traxxas Revo 3.3.
and the T-Maxx 3.3.

FUNCTIONS:
Completely assembled
Plastic telescoping driveshaft with steel universals
Blue rubber boot guards telescoping sections from dirt
Attaches to the differential with one screw pin
Functions on the front or rear, right or left of automobile

CONSISTS OF:
#5458X Yoke, TRAC9798
#5145 Screw Pin, TRAC5145
#5450 Halfshaft, TRAC7450
#5452 U Joint, TRAC7452
#5459 Rubber Boot, TRAC7459
Instruction sheet

REQUIRES:
Installing on chassis

This product compliments the main item here.

54T 0.8 P Spur Gear

This is the 54 Tooth Spur Gear
for the Traxxas Nitro Jato Stadium Truck.

FEATURES:
Nylon building and construction
Black in color
.8 Module pitch

CONSISTS OF:
One 54T 0.8 Pitch Spur Gear

REQUIRES:
Assembly onto automobile

Several others have bought this product in addition to the product that you are currently reading about.

12 X 18 X 4Mm Ball Bearing (2) Blue Rubber Sheild Revo

    These are the replacement Wheel Hub Ball Bearings for
the Traxxas Nitro Revo Beast Truck.

FEATURES:
Stainless Steel Building and construction
Blue Rubber Sealed

CONSISTS OF:
Two 12mm x 18mm Blue Sealed Stainless Wheel Hub Bearings

REQUIRES:
Assembly onto Car

SPECS:
Outer Diameter: 18mm (0.70")
Inner Diameter: 12mm (0.47")
Density: 4mm (0.15")

COMMENTS:
These are for the Within the Wheel Centers, the Truck Needs
4 Total of these Bearings.

The listed below product also sets truly well with the product being gone over.

Half Shaft Set Left Or Right Revo

This is a replacement Half Shaft Set for the Traxxas Revo Truck.
This package consists of a portion of the telescoping drive shafts.

FEATURES:
Black plastic building and construction
Blue rubber shaft boots

CONSISTS OF:
Two half shaft assemblies

REQUIRES:
Nothing. These are direct replacement parts.

SPECS:
Length: 120mm (4.7")

Frequently bought with the product that you are currently reading about.

Bbs Blue Rubber Sealed 6 X 13M

This is a set of Traxxas 6x13x5mm Ball Bearings
for usage on the E-Revo

FUNCTIONS:
Stainless Steel bearing building and construction
Blue rubber dirt guards

CONSISTS OF:
(2) 6x13x5mm ball bearings Part #5180

SPECS:
Inside size: 6mm (0.24")
Outside size: 13mm (0.51")
Width: 5mm (0.20")

Get this product to enhance the one you read around.

Axle Carriers Left & Right (1 Ea) Revo

This is the set of Axle Carriers and Steering Blocks for the Traxxas Revo.
The axle carriers and steering blocks support the stub axles and bolt
    to the upper and lower suspension arms at each wheel.

FEATURES:
Replaces broken axle carriers and steering blocks.
Constructed of black plastic.

INCLUDES:
One set of axle carriers and steering blocks for the Traxxas Revo.

REQUIRES:
Bolting to each suspension arm, installing two 12x18mm ball
    bearings, stub axles, and pillow balls.

Here is a excellent product that several others have bought at the same time.

Axle Carriers Use Larger 6 X 1

These are the Optional Axle Carriers L & R for
usage on the Traxxas Revo series.

FEATURES:
Nylon Building and construction
Black in Color
Permits for Oversized Bearing use

CONSISTS OF:
One Left Axle Provider
One Right Axle Provider
4 Dust Boot Retainers
Two Bearing Spacers

REQUIRES:
Installation

Frequently bought with the product that you are currently reading about.

E-Revo Body Prographix

    This is a PROGRAPHIX Body for the Traxxas E-Revo
Covers and Protects the Vehicle.

FEATURES:
Lexan building and construction
Pre-painted graphics
Body install holes pre-drilled
Pre-cut
Protective movie covers beyond body after surface and is removed
    after completion of paint task

CONSISTS OF:
One painted graphics E-Revo Body
One decal set

REQUIRES:
Lexan safe spray or brush-on paint
Traxxas E-Revo

SPECS:
Length: 500mm (19.7")
Width: 185mm (7.28")
Height: 125mm (4.92")

COMMENT:
Graphics are pre-painted. Needs paint and final
decal application.