Traxxas Driveshaft Assembly (1)

This is the Driveshaft Assembly for the Traxxas Revo 3.3.
and the T-Maxx 3.3.

FEATURES:
Totally assembled
Plastic telescoping driveshaft with steel universals
Blue rubber boot shields telescoping sections from dirt
Attaches to the differential with one screw pin
Works on the front or rear, right or left of car

INCLUDES:
#5458X Yoke, TRAC9798
#5145 Screw Pin, TRAC5145
#5450 Halfshaft, TRAC7450
#5452 U Joint, TRAC7452
#5459 Rubber Boot, TRAC7459
Direction sheet

NEEDS:
Setting up on chassis

This product compliments the main item right here.

54T 0.8 P Spur Gear

This is the 54 Tooth Spur Gear
for the Traxxas Nitro Jato Arena Truck.

FEATURES:
Nylon building
Black in color
.8 Module pitch

INCLUDES:
One 54T 0.8 Pitch Spur Gear

NEEDS:
Assembly onto car

Numerous others have actually purchased this product in addition to the product that you are presently reading about.

12 X 18 X 4Mm Ball Bearing (2) Blue Rubber Sheild Revo

    These are the replacement Wheel Center Ball Bearings for
the Traxxas Nitro Revo Beast Truck.

FEATURES:
Stainless Steel Building and construction
Blue Rubber Sealed

INCLUDES:
Two 12mm x 18mm Blue Sealed Stainless Wheel Center Bearings

NEEDS:
Assembly onto Vehicle

SPECIFICATIONS:
Outer Size: 18mm (0.70")
Inner Size: 12mm (0.47")
Thickness: 4mm (0.15")

COMMENTS:
These are for the Inside of the Wheel Hubs, the Truck Requires
Four Total of these Bearings.

The below product also sets truly well with the product being gone over.

Half Shaft Set Left Or Right Revo

This is a replacement Half Shaft Set for the Traxxas Revo Truck.
This bundle consists of a part of the telescoping drive shafts.

FEATURES:
Black plastic building
Blue rubber shaft boots

INCLUDES:
Two half shaft assemblies

NEEDS:
Nothing. These are direct replacement parts.

SPECS:
Length: 120mm (4.7")

Often purchased with the product that you are presently reading about.

Bbs Blue Rubber Sealed 6 X 13M

This is a set of Traxxas 6x13x5mm Ball Bearings
for usage on the E-Revo

FEATURES:
Stainless Steel bearing building
Blue rubber dirt shields

INCLUDES:
(2) 6x13x5mm ball bearings Part #5180

SPECIFICATIONS:
Inside diameter: 6mm (0.24")
Outdoors diameter: 13mm (0.51")
Width: 5mm (0.20")

Get this product to boost the one you read about.

Axle Carriers Left & Right (1 Ea) Revo

This is the set of Axle Carriers and Steering Blocks for the Traxxas Revo.
The axle carriers and steering blocks support the stub axles and bolt
    to the upper and lower suspension arms at each wheel.

FEATURES:
Changes damaged axle carriers and steering blocks.
Constructed of black plastic.

INCLUDES:
One set of axle carriers and steering blocks for the Traxxas Revo.

REQUIRES:
Bolting to each suspension arm, setting up 2 12x18mm ball
    bearings, stub axles, and pillow balls.

Here is a fantastic product that several others have actually purchased the same time.

Axle Carriers Use Larger 6 X 1

These are the Optional Axle Carriers L & R for
usage on the Traxxas Revo series.

FEATURES:
Nylon Building and construction
Black in Color
Permits for Oversized Bearing use

INCLUDES:
One Left Axle Carrier
One Right Axle Carrier
Four Dust Boot Retainers
Two Bearing Spacers

NEEDS:
Installation

Often purchased with the product that you are presently reading about.

E-Revo Body Prographix

    This is a PROGRAPHIX Body for the Traxxas E-Revo
Covers and Protects the Vehicle.

FEATURES:
Lexan building
Pre-painted graphics
Body install holes pre-drilled
Pre-cut
Protective film covers beyond body after finish and is removed
    after conclusion of paint job

INCLUDES:
One painted graphics E-Revo Body
One decal set

NEEDS:
Lexan safe spray or brush-on paint
Traxxas E-Revo

SPECIFICATIONS:
Length: 500mm (19.7")
Width: 185mm (7.28")
Height: 125mm (4.92")

COMMENT:
Graphics are pre-painted. Requires paint and final
decal application.