Traxxas Driveshaft Assembly (1)

This is the Driveshaft Assembly for the Traxxas Revo 3.3.
and the T-Maxx 3.3.

FEATURES:
Completely put together
Plastic telescoping driveshaft with steel universals
Blue rubber boot guards telescoping sections from dirt
Attaches to the differential with one screw pin
Functions on the front or back, right or left of automobile

INCLUDES:
#5458X Yoke, TRAC9798
#5145 Screw Pin, TRAC5145
#5450 Halfshaft, TRAC7450
#5452 U Joint, TRAC7452
#5459 Rubber Boot, TRAC7459
Direction sheet

REQUIRES:
Setting up on chassis

This product compliments the main item below.

54T 0.8 P Spur Gear

This is the 54 Tooth Spur Gear
for the Traxxas Nitro Jato Arena Truck.

FEATURES:
Nylon construction
Black in color
.8 Module pitch

INCLUDES:
One 54T 0.8 Pitch Spur Gear

REQUIRES:
Assembly onto automobile

Several others have actually purchased this product in addition to the product that you are presently reading about.

12 X 18 X 4Mm Ball Bearing (2) Blue Rubber Sheild Revo

    These are the replacement Wheel Center Ball Bearings for
the Traxxas Nitro Revo Monster Truck.

FEATURES:
Stainless Steel Construction
Blue Rubber Sealed

INCLUDES:
2 12mm x 18mm Blue Sealed Stainless Wheel Center Bearings

REQUIRES:
Assembly onto Vehicle

SPECS:
Outer Diameter: 18mm (0.70")
Inner Diameter: 12mm (0.47")
Density: 4mm (0.15")

REMARKS:
These are for the Inside of the Wheel Centers, the Truck Needs
4 Overall of these Bearings.

The listed below product additionally pairs actually well with the product being reviewed.

Half Shaft Set Left Or Right Revo

This is a replacement Half Shaft Set for the Traxxas Revo Truck.
This bundle includes a portion of the telescoping drive shafts.

FEATURES:
Black plastic construction
Blue rubber shaft boots

INCLUDES:
2 half shaft assemblies

REQUIRES:
Nothing. These are direct replacement parts.

SPECS:
Length: 120mm (4.7")

Frequently purchased with the product that you are presently reading about.

Bbs Blue Rubber Sealed 6 X 13M

This is a set of Traxxas 6x13x5mm Ball Bearings
for use on the E-Revo

FEATURES:
Stainless Steel bearing construction
Blue rubber dirt guards

INCLUDES:
(2) 6x13x5mm ball bearings Part #5180

SPECS:
Inside diameter: 6mm (0.24")
Outside diameter: 13mm (0.51")
Width: 5mm (0.20")

Get this product to boost the one you read around.

Axle Carriers Left & Right (1 Ea) Revo

This is the set of Axle Carriers and Steering Blocks for the Traxxas Revo.
The axle providers and steering blocks support the stub axles and bolt
    to the upper and lower suspension arms at each wheel.

FEATURES:
Changes broken axle providers and steering blocks.
Constructed of black plastic.

INCLUDES:
One set of axle providers and steering blocks for the Traxxas Revo.

REQUIRES:
Bolting to each suspension arm, setting up two 12x18mm ball
    bearings, stub axles, and pillow balls.

Right here is a great product that lots of others have actually bought at the same time.

Axle Carriers Use Larger 6 X 1

These are the Optional Axle Carriers L & R for
use on the Traxxas Revo series.

FEATURES:
Nylon Construction
Black in Color
Enables for Oversized Bearing utilize

INCLUDES:
One Left Axle Provider
One Right Axle Provider
4 Dust Boot Retainers
2 Bearing Spacers

REQUIRES:
Installation

Frequently purchased with the product that you are presently reading about.

E-Revo Body Prographix

    This is a PROGRAPHIX Body for the Traxxas E-Revo
Covers and Secures the Vehicle.

FEATURES:
Lexan construction
Pre-painted graphics
Body install holes pre-drilled
Pre-cut
Protective film covers beyond body after surface and is gotten rid of
    after completion of paint task

INCLUDES:
One painted graphics E-Revo Body
One decal set

REQUIRES:
Lexan safe spray or brush-on paint
Traxxas E-Revo

SPECS:
Length: 500mm (19.7")
Width: 185mm (7.28")
Height: 125mm (4.92")

COMMENT:
Graphics are pre-painted. Needs paint and final
decal application.