Traxxas Driveshaft Assembly Front Heavy Duty Stampede 4X4

This is the Strong Driveshaft Assembly for the Slash 4x4 from Traxxas

FEATURES:
Black plastic and steel construction

INCLUDES:
Front driveshaft assembly
Screw pin

REQUIRES:
Installation on vehicle

The listed below thing also sets really well with the thing being reviewed.

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Strong Driveshaft Assembly for the Slash 4x4 from Traxxas

FEATURES:
Black plastic and steel construction

INCLUDES:
Rear driveshaft assembly
Screw pin

REQUIRES:
Installation on vehicle

This is a wonderful addition to the thing currently being reviewed.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing construction
Blue rubber dirt guards

INCLUDES:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside diameter: 3/16" (5mm)
Outdoors diameter: 7/16" (11mm)
Width: 5/32" (4mm)

Lots of others have acquired this thing along with the thing that you are currently reading about.

Slipper Clutch Complete Stampede 4X4

This is the Total Slipper Clutch Set for the Slash 4X4 from Traxxas.

FEATURES:
Total slipper clutch assembly
Pre-assembled

INCLUDES:
2 nuts
1 spring
1 metal plate
1 pin
3 pads
2 washers
54T spur gear

REQUIRES:
Installation in vehicle

Right here is a fantastic thing that numerous others have purchased the same time.

Steering Blocks, Left & Right

These are the Steering Blocks for the Traxxas Slash 4x4.

FEATURES:
Solidified plastic construction
Black in color

INCLUDES:
2 steering obstructs

REQUIRES:
Installation on guiding assembly

SPECS:
Length: 35mm (1.38")
Width: 32mm (1.26")

You will certainly like this item if you have the item above discussed.

Front Or Rear A-Arms For Traxxas Slash 4X4 And Rustler 4X4, Blac

These are the optional RPM Strong Front/Rear A-Arms
for the Traxxas Slash 4x4.

FEATURES:
Black in color
Plastic constrution

INCLUDES:
2 Front/Rear A-Arms

REQUIRES:
Installation at front or rear suspension

SPECS:
Length: 3.96" (100.5mm)
Width: 1.79" (45.5mm) at widest point
Thickness: 0.31" (8mm)

COMMENTS:
Also available in Blue (RPMC0705)

This thing is regularly acquired with the above pointed out thing.

Body Mount (1)/Body Mount Pos

This is the Front/Rear Body Mount for the Traxxas Slash 4x4.

FEATURES:
Solidified plastic construction
Black in color

INCLUDES:
One body install
2 body install posts

REQUIRES:
Installation on chassis

SPECS:
Length: 126mm (4.96")
Width: 24mm (0.95")

Frequently acquired with the thing that you are currently reading about.

Caster Blocks (C-Hubs), Left &

These are the Caster Blocks (C-Hubs) for the Traxxas Slash 4x4.

FEATURES:
Solidified plastic construction
Black in color

INCLUDES:
One left caster block
One right caster block

REQUIRES:
Installation on Slash

SPECS:
Length: 49mm (1.93")
Width: 29.5mm (1.16")

This is a wonderful addition to the thing currently being reviewed.

54T 0.8 P Spur Gear

This is the 54 Tooth Spur Equipment
for the Traxxas Nitro Jato Stadium Truck.

FEATURES:
Nylon construction
Black in color
.8 Module pitch

INCLUDES:
One 54T 0.8 Pitch Spur Equipment

REQUIRES:
Assembly onto vehicle

Frequently acquired with the thing that you are currently reading about.

10 X 15 X 4Mm Ball Bearing (2) Blue Rubber Sheild Revo

This is a set of 10x15mm Ball Bearings for use on the Traxxas Revo.

FEATURES:
Steel Building
Shielded with blue rubber seals

INCLUDES:
2 Ball Bearings

REQUIRES:
Assembly to vehicle

SPECS:
Inner Size: 10mm
Outer Size: 15mm
Side Thickness: 4mm

COMMENTS:
These bearings are used to support the Main Clutch (one needed).