Traxxas Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Sturdy Driveshaft Assembly for the Slash 4x4 from Traxxas

FUNCTIONS:
Black plastic and steel building

CONSISTS OF:
Rear driveshaft assembly
Screw pin

NEEDS:
Installation on vehicle

Get this item to improve the one you read about.

Driveshaft Assembly Front Heavy Duty Stampede 4X4

This is the Sturdy Driveshaft Assembly for the Slash 4x4 from Traxxas

FUNCTIONS:
Black plastic and steel building

CONSISTS OF:
Front driveshaft assembly
Screw pin

NEEDS:
Installation on vehicle

The below item also pairs really well with the item being reviewed.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building
Blue rubber dirt shields

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside diameter: 3/16" (5mm)
Outside diameter: 7/16" (11mm)
Width: 5/32" (4mm)

You will certainly love this product if you have the product previously mentioned.

Hex Hubs & Axle Pins Slash

These are the replacement rear wheel adapters for the Hawk, Hawk 2, Bullet,
Sledgehammer, Eagle, and Blue Eagle LS. These are hex nuts that connect the
rear wheels to the axles.

INCLUDES:
2- plastic hex collars (wheel adapters)
4- stub axle pins

WAJ
1/16/93

Lots of others have gotten this item together with the item that you are currently checking out.

Teflon Washers 5 X 8Mm (20)

These are Replacement Washers from Traxxas.

FEATURES:
Black plastic construction.
Used on the axles and in the transmission.

INCLUDES:
(20) Washers

SPECIFICATIONS:
Size: 5x8mm
Density: 0.5mm

Want an additional fantastic item to enhance the above discussed item?

Planetary Gear Diff W/Steel Ring Gear Slash/Bandit /Stampe

This is the Total Planetary Equipment Differential With Steel Ring Equipment
for the Traxxas Outlaw, Stampede and Rustler.

FEATURES:
Metal equipment shafts
Metal and plastic primary differential

CONSISTS OF:
Main differential with steel ring equipment
Planetary gears and shafts
Sun gears and shafts
Silicone grease

NEEDS:
Installation on the vehicle

REMARKS:
For primary differential w/ steel ring - TRAC6380
Planet equipment shafts - TRAC6382
Silicon grease _- TRAC6037

This item is regularly gotten with the above discussed item.

30T Idler Gear Steel

This is the optional Steel Idler Equipment for numerous Traxxas Vehicles.

FEATURES:
Steel building

CONSISTS OF:
One steel 30T idler equipment

NEEDS:
Installation on vehicle

The below item also pairs really well with the item being reviewed.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel building
_
Roll pin pre-installed

CONSISTS OF:
One slipper clutch set

SPECIFICATIONS:
Length: 1.98" (50mm)
Diameter: .21" ( 5mm)

REMARKS:
This part will fit both the standard and XL version of the Rustler
or Stampede.

This item compliments the above reviewed item.

Gearbox Halves L&R Grey

This is a Left and Right Gearbox half with Idler Shaft for the
Traxxas Stampede and Traxxas Rustler.

FEATURES:
Gray plastic building
Steel idler shaft

CONSISTS OF:
One gearbox
One idler shaft

REMARKS:
This part fit the standard and XL version of both the Stampede
and Rustler.

This is a wonderful addition to the item currently being reviewed.

49Mm Turnbuckles Camber Link Rr

These are the Traxxas 49mm Turnbuckle Camber Hyperlinks
for the Outlaw, Rustler VXL and Stampede VXL.

FEATURES:
Metal and Nylon Construction
Silver and Black in Color
Put together w/Rod Ends

CONSISTS OF:
Two rear 49mm (82mm center to center) turnbuckles

NEEDS:
Installation on the vehicle