Traxxas Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Sturdy Driveshaft Assembly for the Slash 4x4 from Traxxas

FEATURES:
Black plastic and steel building and construction

CONSISTS OF:
Rear driveshaft assembly
Screw pin

NEEDS:
Setup on car

Get this product to enhance the one you read about.

Driveshaft Assembly Front Heavy Duty Stampede 4X4

This is the Sturdy Driveshaft Assembly for the Slash 4x4 from Traxxas

FEATURES:
Black plastic and steel building and construction

CONSISTS OF:
Front driveshaft assembly
Screw pin

NEEDS:
Setup on car

The below product also sets truly well with the product being talked about.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building and construction
Blue rubber dirt guards

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside size: 3/16" (5mm)
Outdoors size: 7/16" (11mm)
Width: 5/32" (4mm)

You will like this item if you have the item previously pointed out.

Hex Hubs & Axle Pins Slash

These are the replacement rear wheel adapters for the Hawk, Hawk 2, Bullet,
Sledgehammer, Eagle, and Blue Eagle LS. These are hex nuts that link the
rear wheels to the axles.

INCLUDES:
2- plastic hex collars (wheel adapters)
4- stub axle pins

WAJ
1/16/93

Several others have purchased this product along with the product that you are presently reviewing.

Teflon Washers 5 X 8Mm (20)

These are Replacement Washers from Traxxas.

FEATURES:
Black plastic construction.
Used on the axles and in the transmission.

INCLUDES:
(20) Washers

SPECS:
Size: 5x8mm
Density: 0.5mm

Want an additional terrific product to compliment the above mentioned product?

Planetary Gear Diff W/Steel Ring Gear Slash/Bandit /Stampe

This is the Total Planetary Gear Differential With Steel Ring Gear
for the Traxxas Bandit, Stampede and Rustler.

FEATURES:
Metal equipment shafts
Metal and plastic primary differential

CONSISTS OF:
Main differential with steel ring equipment
Planetary gears and shafts
Sun gears and shafts
Silicone grease

NEEDS:
Setup on the car

REMARKS:
For primary differential w/ steel ring - TRAC6380
Planet equipment shafts - TRAC6382
Silicon grease _- TRAC6037

This product is regularly purchased with the above mentioned product.

30T Idler Gear Steel

This is the optional Steel Idler Gear for many Traxxas Vehicles.

FEATURES:
Steel building and construction

CONSISTS OF:
One steel 30T idler equipment

NEEDS:
Setup on car

The below product also sets truly well with the product being talked about.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel building and construction
_
Roll pin pre-installed

CONSISTS OF:
One slipper clutch set

SPECS:
Length: 1.98" (50mm)
Diameter: .21" ( 5mm)

REMARKS:
This part will fit both the requirement and XL version of the Rustler
or Stampede.

This product compliments the above talked about product.

Gearbox Halves L&R Grey

This is a Left and Right Gearbox half with Idler Shaft for the
Traxxas Stampede and Traxxas Rustler.

FEATURES:
Gray plastic building and construction
Steel idler shaft

CONSISTS OF:
One gearbox
One idler shaft

REMARKS:
This part fit the requirement and XL version of both the Stampede
and Rustler.

This is a superb enhancement to the product presently being talked about.

49Mm Turnbuckles Camber Link Rr

These are the Traxxas 49mm Turnbuckle Camber Hyperlinks
for the Bandit, Rustler VXL and Stampede VXL.

FEATURES:
Metal and Nylon Construction
Silver and Black in Color
Put together w/Rod Ends

CONSISTS OF:
2 rear 49mm (82mm center to center) turnbuckles

NEEDS:
Setup on the car