Traxxas Diff Carrier / X-Ring Gaskets (2) / Ring Gear Gask Et/ 6 X 1

This is the Diff Carrier/Gasket Set for the Traxxas Revo.

FEATURES:
Plastic Diff Carrier
Blue Rubber Shaft Gaskets
Black Rubber Diff Carrier Gaskets
Gray Washer

SUCHES AS:
One Diff Carrier
Two Blue Rubber Shaft Gaskets
One Black Rubber Diff Carrier Gaskets
One Gray Washer

REQUIRES:
Assembly to vehicle

This product is often acquired with the above discussed product.

Gear Set, Differential

This is the Differential Equipment Set for the Traxxas Revo and E-Maxx.

FEATURES:
Steel building

SUCHES AS:
Two Output Gears
Two Spider Equipments
Spider Gear Shaft and Diff Carrier Assistance
Guideline Sheet

REQUIRES:
Diff lube;
10K weight TRAC5135 50K weight TRAC5137
30K weight TRAC5136 Multi-weight set TRAC9136

Regularly acquired with the product that you are currently reading about.

Diff Ring Gear / Pinion Gear Revo

This is the Differential Ring Equipment and Pinion
for use with the Traxxas Revo 3.3.

FEATURES:
Direct replacement part

SUCHES AS:
One differential ring gear
One pinion gear

REQUIRES:
Traxxas Revo 3.3
2.5x8mm cap head screws (TRAC3965)

Regularly acquired with the product that you are currently reading about.



This is a CVD Coupling Rebuild Kit used for various Beast Trucks.
Works for the TMaxx/Emaxx, Revo, Tamiya TNX, Savage 21 & 25, Losi LST

FEATURES:
Black oxide rust preventive surface on the coupling

SUCHES AS:
(2) Cross pin 2.5 x 16mm
(2) Coupling 6mm size x 9mm length
(2) Set screw 4.0 x 3mm

You will enjoy this product if you have the product above mentioned.

Gear Set, Differential (Output Gears, Spider Gears/ Shaft)

This is the Differential Equipment Set for the Traxxas X-01 Vehicle, TRAD42**.

FEATURES:
Hardened steel building

SUCHES AS:
Two Output Gears
Two Spider Equipments
One Spider Gear Shaft
One Carrier Assistance

Many others have actually acquired this product along with the product that you are currently reading about.

8 X 16 X 5Mm Ball Bearing (2) Blue Rubber Sheild R Evo

    These are the replacement Differential Bearings for
the Traxxas Nitro Revo Beast Truck.

FEATURES:
Stainless Construction
Blue Rubber Sealed

SUCHES AS:
Two 8mm x 16mm Rubber Sealed Bearings

REQUIRES:
Assembly onto Car

SPECIFICATIONS:
Inner Diameter: 8mm (0.31")
Outer Diameter: 16mm (0.62")
Density: 5mm (0.19")

This is a wonderful enhancement to the product currently being gone over.

10 X 15 X 4Mm Ball Bearing (2) Blue Rubber Sheild Revo

This is a set of 10x15mm Ball Bearings for use on the Traxxas Revo.

FEATURES:
Steel Construction
Shielded with blue rubber seals

SUCHES AS:
Two Ball Bearings

REQUIRES:
Assembly to vehicle

SPECIFICATIONS:
Inner Diameter: 10mm
External Diameter: 15mm
Side Density: 4mm

COMMENTS:
These bearings are used to support the Primary Clutch (one required).

Many others have actually acquired this product along with the product that you are currently reading about.

12 X 18 X 4Mm Ball Bearing (2) Blue Rubber Sheild Revo

    These are the replacement Wheel Hub Ball Bearings for
the Traxxas Nitro Revo Beast Truck.

FEATURES:
Stainless Steel Construction
Blue Rubber Sealed

SUCHES AS:
Two 12mm x 18mm Blue Sealed Stainless Wheel Hub Bearings

REQUIRES:
Assembly onto Car

SPECIFICATIONS:
Outer Diameter: 18mm (0.70")
Inner Diameter: 12mm (0.47")
Density: 4mm (0.15")

COMMENTS:
These are for the Within of the Wheel Hubs, the Truck Requires
4 Total of these Bearings.

Regularly acquired with the product that you are currently reading about.

Pivot Ball Caps & Dust Boots

This is the replacement Pivot Ball and Dust Cap Boot Set
    for the Traxxas Revo, E-Revo and T-Maxx 3.3 vehicles.

FEATURES:
Nylon and Rubber Construction
Blue and Black in Color

SUCHES AS:
4 Blue Rubber Pivot Ball Boots
4 Black Dust Boot Retainer
4 Blue Notched Dust Boot Retainer
4 Blue Rubber Boot Plugs
4 nylon Pivot Ball Retainers
Guideline sheet

REQUIRES:
Two packages had to complete truck