Traxxas Chassis Braces, Lower (Black)

This is the Lower Chassis Brace for the Traxxas E-Maxx.

FEATURES:
Nylon construction, black in color
Replaces used or harmed lower chassis braces

CONSISTS OF:
Right and left lower chassis braces

REQUIRES:
Setup on the E-Maxx

SPECS:
Length: 9.44" (240mm)
Width: 1.57" (40mm)
Density: .43" (11mm)

This item praises the main item here.

Chassis, E-Maxx (Long Wheelbas

This is the Long Wheelbase Chassis for the Traxxas E-Maxx.

FEATURES:
Nylon construction, gray in color
Replaces used or damaged chassis

CONSISTS OF:
One long wheelbase chassis

REQUIRES:
Setup on the E-Maxx

SPECS:
Length: 11.5" (292.1mm)
Width: 6.5" (165.1mm)

You will enjoy this thing if you have the thing above discussed.

Box, Receiver Sealed W/Silicon

This is the Receiver Box for the Traxxas E-Maxx Truck.

FEATURES:
Replaces damaged receiver boxes
Constructed of black plastic

CONSISTS OF:
One top and bottom half receiver box for the Traxxas E-Maxx
Hardware

REQUIRES:
Installing receiver and bolting receiver box to chassis.

Below is one more item that praises the item being discussed.

Motor Plate For Single Motor

This is the optional Single Motor Plate for the
Traxxas E-Maxx 16.8V RTR.

FEATURES:
Aluminum construction, blue in color
Developed for a tidy install of a single brushless motor system in
the E-Maxx 16.8V RTR (requires gear cover number TRAC3997)

CONSISTS OF:
One Aluminum Motor Plate

REQUIRES:
Setup and motor cover number TRAC3997

The listed below item also sets truly well with the item being discussed.

Center Half Shafts E-Revo

This is the Center Half Shaft Set for the Traxxas E-Revo

FEATURES:
Plastic construction, black in color

CONSISTS OF:
Center half shafts (3 internal splined and 2 external splined)

REQUIRES:
Setup on the vehicle

SPECS:
Diameter: 17.2mm (0.68")

Lots of others have acquired this item together with the item that you are currently reading about.

Skid Plate Gray E-Maxx

This is the Transmission Skid Plate
for the Traxxas E-Maxx.

FEATURES:
Gray nylon construction

CONSISTS OF:
One nylon transmission skid plate

REQUIRES:
Setup on the E-Maxx

SPECS:
Length: 4.60" (117mm)
Width: 2.40" (61mm)

Want one more fantastic item to compliment the above pointed out item?

3 X 12Mm Cntrsnk Machine Screw (6)

This is a bundle of 6 3x12mm Traxxas Countersunk Hex Head Screws.

FEATURES:
Steel construction, Black in color
Used on the Traxxas Revo beast truck, can also be used in any
    application where a 3x12mm countersunk screw is needed

CONSISTS OF:
Six 3x12mm Traxxas Countersunk Hex Screws

REQUIRES:
2mm hex head wrench, GPMR8011

SPECS:
Length: 12mm
Diameter: 3mm

You will enjoy this thing if you have the thing above discussed.



This is the 3-Channel Futaba 3PRKA 2.4GHz FHSS Radio System
with the R203GF Receiver.

FEATURES:
Perfect upgrade for radios found in RTR automobiles
Throttle and guiding trim and reverse
Guiding dual rate dial
Throttle end point adjustment
Channel 3 switch
Throttle fail safe
One year minimal warranty through Pastime Solutions starting at date
    of purchase

CONSISTS OF:
Futaba 3PRKA 2.4GHz FHSS Transmitter, R203GF Receiver, Guideline
    Handbook and On/Off Change

REQUIRES:
Servos of modeler's choice
4 AA batteries for transmitter

SPECS:
Transmitter:
Transferring Frequency: 2.4GHz band
Power Requirement: 4 AA cells
Existing Drain: 100mA or less

    Receiver;
Measurements: 1.54 x 1.02 x 0.39" (39 x 26 x 10mm)
Weight: 0.28oz (8g)
Operating Voltage: 4.8 - 7.4V (shared with servo)
Battery Fail Safe Voltage: 3.8V*
Existing Drain: 30mA at no signal
*Battery fail safe voltage is set for 4-cell NiCd/NiMH battery
Battery F/S does not work effectively when other kind of battery is used

COMMENTS:
2.4GHz FHSS is not suitable with FASST systems.
Normal mode frame rate is (FHSS/S-FHSS) 13.63ms and accepts any
kind of servos or peripherals.
High-Speed mode (in 4PL tx only), with an output of 6.8ms accepts
    digital servos consisting of the BLS series and most peripheral
    devices such as brushless ESCs