Traxxas Chassis Braces, Lower (Black)

This is the Lower Chassis Brace for the Traxxas E-Maxx.

FEATURES:
Nylon building and construction, black in color
Replaces worn or harmed lower chassis braces

INCLUDES:
Right and left lower chassis braces

REQUIRES:
Setup on the E-Maxx

SPECS:
Length: 9.44" (240mm)
Width: 1.57" (40mm)
Thickness: .43" (11mm)

This thing compliments the main item here.

Chassis, E-Maxx (Long Wheelbas

This is the Long Wheelbase Chassis for the Traxxas E-Maxx.

FEATURES:
Nylon building and construction, gray in color
Replaces worn or damaged chassis

INCLUDES:
One long wheelbase chassis

REQUIRES:
Setup on the E-Maxx

SPECS:
Length: 11.5" (292.1mm)
Width: 6.5" (165.1mm)

You will enjoy this thing if you have the thing previously mentioned.

Box, Receiver Sealed W/Silicon

This is the Receiver Box for the Traxxas E-Maxx Truck.

FEATURES:
Replaces damaged receiver boxes
Constructed of black plastic

INCLUDES:
One top and bottom half receiver box for the Traxxas E-Maxx
Hardware

REQUIRES:
Setting up receiver and bolting receiver box to chassis.

Here is an additional thing that compliments the thing being gone over.

Motor Plate For Single Motor

This is the optional Single Motor Plate for the
Traxxas E-Maxx 16.8V RTR.

FEATURES:
Aluminum building and construction, blue in color
Developed for a clean install of a single brushless motor system in
the E-Maxx 16.8V RTR (requires gear cover number TRAC3997)

INCLUDES:
One Aluminum Motor Plate

REQUIRES:
Setup and motor cover number TRAC3997

The listed below thing also sets actually well with the thing being gone over.

Center Half Shafts E-Revo

This is the Center Half Shaft Set for the Traxxas E-Revo

FEATURES:
Plastic building and construction, black in color

INCLUDES:
Center half shafts (3 internal splined and two external splined)

REQUIRES:
Setup on the vehicle

SPECS:
Size: 17.2mm (0.68")

Lots of others have bought this thing in addition to the thing that you are currently reading about.

Skid Plate Gray E-Maxx

This is the Transmission Skid Plate
for the Traxxas E-Maxx.

FEATURES:
Gray nylon building and construction

INCLUDES:
One nylon transmission skid plate

REQUIRES:
Setup on the E-Maxx

SPECS:
Length: 4.60" (117mm)
Width: 2.40" (61mm)

Want an additional terrific thing to compliment the above pointed out thing?

3 X 12Mm Cntrsnk Machine Screw (6)

This is a bundle of six 3x12mm Traxxas Countersunk Hex Head Screws.

FEATURES:
Steel building and construction, Black in color
Utilized on the Traxxas Revo beast truck, can likewise be utilized in any
    application where a 3x12mm countersunk screw is needed

INCLUDES:
Six 3x12mm Traxxas Countersunk Hex Screws

REQUIRES:
2mm hex head wrench, GPMR8011

SPECS:
Length: 12mm
Size: 3mm

You will enjoy this thing if you have the thing previously mentioned.



This is the 3-Channel Futaba 3PRKA 2.4GHz FHSS Radio System
with the R203GF Receiver.

FEATURES:
Perfect upgrade for radios discovered in RTR automobiles
Throttle and guiding trim and reverse
Steering double rate dial
Throttle end point modification
Channel 3 switch
Throttle fail safe
One year minimal guarantee through Pastime Solutions beginning at date
    of purchase

INCLUDES:
Futaba 3PRKA 2.4GHz FHSS Transmitter, R203GF Receiver, Direction
    Handbook and On/Off Change

REQUIRES:
Servos of modeler's option
Four AA batteries for transmitter

SPECS:
Transmitter:
Sending Frequency: 2.4GHz band
Power Requirement: Four AA cells
Present Drain: 100mA or less

    Receiver;
Measurements: 1.54 x 1.02 x 0.39" (39 x 26 x 10mm)
Weight: 0.28oz (8g)
Operating Voltage: 4.8 - 7.4V (shared with servo)
Battery Fail Safe Voltage: 3.8V*
Present Drain: 30mA at no signal
*Battery fail safe voltage is set for 4-cell NiCd/NiMH battery
Battery F/S does not work properly when other type of battery is utilized

REMARKS:
2.4GHz FHSS is not suitable with FASST systems.
Normal mode frame rate is (FHSS/S-FHSS) 13.63ms and accepts any
type of servos or peripherals.
High-Speed mode (in 4PL tx only), with an output of 6.8ms accepts
    digital servos consisting of the BLS series and most peripheral
    equipment such as brushless ESCs