Traxxas Bulkhead Tie Bars, Front & Rea

This is the replacement Bulkhead Tie Bars for the Traxxas Slash 4X4.

FEATURES:
Aluminum building
Anodized blue in color

CONSISTS OF:
2 bulkhead tie bars (front and rear)

REQUIRES:
Setup on the Slash 4X4

Frequently gotten with the thing that you are presently reviewing.

Suspension Pin Set, Complete Frt & Rr Includes Frt & Rr Swa

This is the Suspension Pin Set for the Traxxas Slash 4X4.
The hinge pins hold the suspension arms to the bulkheads

FEATURES:
Long lasting steel building
Silver in color

CONSISTS OF:
4 51.5mm pins
4 30mm pins

REQUIRES:
Setup on the Slash 4x4

This is a wonderful addition to the thing presently being discussed.

Alum Bearing Adapter Slash 4X4

This is an optional Bearing Adapter for the Slash 4X4.

FEATURES:
6061-T6 anodized blue aluminum building
Steel 10x15x4mm ball bearing with blue rubber seal
Utilized on slipper shaft

CONSISTS OF:
One aluminum adapter
One 10x15x4mm ball bearing

REQUIRES:
Setup on to slipper shaft
Staying clutch pieces

Frequently gotten with the thing that you are presently reviewing.

Diff Ring Gear / Pinion Gear Revo

This is the Differential Ring Gear and Pinion
for use with the Traxxas Revo 3.3.

FEATURES:
Direct replacement part

CONSISTS OF:
One differential ring gear
One pinion gear

REQUIRES:
Traxxas Revo 3.3
2.5x8mm cap head screws (TRAC3965)

Here is a excellent thing that lots of others have actually bought at the very same time.

Drive Hub, Frt, Hardened Steel (1) Screw Pin, (1) Fits Slash

This is the Front Hardened Steel Drive Center for use on the Traxxas Slash 4x4.

FEATURES:
Solidified steel building

CONSISTS OF:
One Drive Center
One Screw Pin

REQUIRES:
Setup on the vehicle

SPECS:
Length: 19mm (0.75")
Diameter: 12mm (0.47")

Several others have actually gotten this thing together with the thing that you are presently reviewing.

58Mm Turnbuckles Camber Links (Front Or Rear) (Ass Embled W/

These are the 58mm Turnbuckle Camber Links
for the Traxxas Nitro Jato Arena Truck.

FEATURES:
Metal and Nylon Building and construction
Silver and Black in Color
Put together w/Rod Ends
Can be Utilized on Front or Rear

CONSISTS OF:
2 58mm Threaded Rods
4 3mm Ball Ends
4 3mm Hollow Balls

REQUIRES:
Assembly onto Automobile

This is a wonderful addition to the thing presently being discussed.

Slipper Clutch Complete Stampede 4X4

This is the Complete Slipper Clutch Set for the Slash 4X4 from Traxxas.

FEATURES:
Complete slipper clutch assembly
Pre-assembled

CONSISTS OF:
2 nuts
1 spring
1 metal plate
1 pin
3 pads
2 washers
54T spur gear

REQUIRES:
Setup in vehicle

You will like this thing if you have the thing earlier stated.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building
Blue rubber dirt guards

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside size: 3/16" (5mm)
Externally size: 7/16" (11mm)
Width: 5/32" (4mm)

Here is one more thing that compliments the thing being discussed.

8 X 16 X 5Mm Ball Bearing (2) Blue Rubber Sheild R Evo

    These are the replacement Differential Bearings for
the Traxxas Nitro Revo Monster Truck.

FEATURES:
Stainless Building and construction
Blue Rubber Sealed

CONSISTS OF:
2 8mm x 16mm Rubber Sealed Bearings

REQUIRES:
Assembly onto Automobile

SPECS:
Inner Diameter: 8mm (0.31")
Outer Diameter: 16mm (0.62")
Density: 5mm (0.19")

This thing compliments the above discussed thing.

10 X 15 X 4Mm Ball Bearing (2) Blue Rubber Sheild Revo

This is a set of 10x15mm Ball Bearings for use on the Traxxas Revo.

FEATURES:
Steel Building and construction
Shielded with blue rubber seals

CONSISTS OF:
2 Ball Bearings

REQUIRES:
Assembly to vehicle

SPECS:
Inner Diameter: 10mm
Outer Diameter: 15mm
Side Density: 4mm

COMMENTS:
These bearings are used to support the Primary Clutch (one needed).