Traxxas Box, Receiver For Stmpd, Rstlr, Bandt

This is the Receiver Box for use on the
Traxxas Stampede, Rustler, and Bandit Vehicles.

FEATURES:
Nylon building
Black in color

INCLUDES:
One Receiver Box
One Rubber Seal
Foam Padding
Two 2.5x8mm Cap Head Screws
Two 3x10mm Cap Head Screws
Two 2.5x10mm Cap Head Screws
One Tube of Grease
Direction sheet

REQUIRES:
Installation on the automobile

SPECIFICATIONS:
Length: 78mm (3.07")
Width: 35mm (1.4")
Height: 33mm (1.3")

This product praises the main item below.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building
Blue rubber dirt shields

INCLUDES:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside size: 3/16" (5mm)
Outside size: 7/16" (11mm)
Width: 5/32" (4mm)

Get this product to enhance the one you are reading around.

Hc Connector M/F (1) Available Only From

This is the Male/Female Traxxas Connectors Plugs Just (No Wires).

FEATURES:
Shrouded wire connections (no diminish tube needed)
Wide surface area, gold-plated terminals
Reverse polarity security makes it difficult to connect backwards
Textured surface for simple gripping
Suitable with high-current 12-gauge wire
Protect, favorable locking spring crammed terminals for consistent
    contact
Numerous locking barbs keep terminals protect

INCLUDES:
One black female plastic connector
One black male plastic connector
Two sets of gold metal pins
Direction sheet

REQUIRES:
Soldering wires to the metal pins

The listed below product additionally sets really well with the product being discussed.

Mounting Plate For Stampede Esc

This is the ESC and Receiver Box Mounting Plate for use on the
Traxxas Stampede.

FEATURES:
Nylon building
Black in color

INCLUDES:
One Mounting Plate
4 3x7.5mm Flanged Button Head Screws
Two 3x12mm Flanged Button Head Screws

REQUIRES:
Installation on the automobile

SPECIFICATIONS:
Length: 87mm (3.4")
Width: 60mm (2.4")
Height: 10mm (0.39")

This is a superb addition to the product currently being discussed.

Front Axles (2) (R & S)

This is a Pair of Stock Replacement Front Axles for the Rustler and Stampede.
These are situated in the front steering blocks.

FEATURES:
Steel building
Natural color

INCLUDES:
Two front axles

REQUIRES:
Absolutely nothing. These are direct replacement parts.

SPECS:
Length: 32mm (1.26")
Diameter: 5mm

COMMENTS:
These will not work for the nitro variations. For that axle, use
    TRAC2536.

This product is regularly acquired with the above stated product.

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Heavy Duty Driveshaft Assembly for the Slash 4x4 from Traxxas

FEATURES:
Black plastic and steel building

INCLUDES:
Rear driveshaft assembly
Screw pin

REQUIRES:
Installation on automobile

This product praises the main item below.

30T Idler Gear Steel

This is the optional Steel Idler Equipment for many Traxxas Vehicles.

FEATURES:
Steel building

INCLUDES:
One steel 30T idler equipment

REQUIRES:
Installation on automobile

Lots of others have acquired this product in addition to the product that you are currently reviewing.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel building
_
Roll pin pre-installed

INCLUDES:
One slipper clutch set

SPECIFICATIONS:
Length: 1.98" (50mm)
Diameter: .21" ( 5mm)

COMMENTS:
This part will fit both the requirement and XL variation of the Rustler
or Stampede.