Traxxas Box, Receiver For Stmpd, Rstlr, Bandt

This is the Receiver Box for use on the
Traxxas Stampede, Rustler, and Outlaw Vehicles.

FEATURES:
Nylon construction
Black in color

INCLUDES:
One Receiver Box
One Rubber Seal
Foam Cushioning
2 2.5x8mm Cap Head Screws
2 3x10mm Cap Head Screws
2 2.5x10mm Cap Head Screws
One Tube of Grease
Guideline sheet

NEEDS:
Installation on the automobile

SPECIFICATIONS:
Length: 78mm (3.07")
Width: 35mm (1.4")
Height: 33mm (1.3")

This product compliments the main item right here.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing construction
Blue rubber dirt guards

INCLUDES:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside diameter: 3/16" (5mm)
Outdoors diameter: 7/16" (11mm)
Width: 5/32" (4mm)

Get this product to boost the one you are reading about.

Hc Connector M/F (1) Available Only From

This is the Male/Female Traxxas Connectors Plugs Just (No Wires).

FUNCTIONS:
Shrouded wire connections (no diminish tube required)
Wide area, gold-plated terminals
Reverse polarity protection makes it impossible to connect backwards
Textured surface for easy gripping
Suitable with high-current 12-gauge wire
Secure, positive locking spring crammed terminals for constant
    contact
Multiple locking barbs keep terminals secure

INCLUDES:
One black female plastic adapter
One black male plastic adapter
2 sets of gold metal pins
Guideline sheet

NEEDS:
Soldering wires to the metal pins

The listed below product also pairs actually well with the product being discussed.

Mounting Plate For Stampede Esc

This is the ESC and Receiver Box Mounting Plate for use on the
Traxxas Stampede.

FEATURES:
Nylon construction
Black in color

INCLUDES:
One Mounting Plate
4 3x7.5mm Flanged Button Head Screws
2 3x12mm Flanged Button Head Screws

NEEDS:
Installation on the automobile

SPECIFICATIONS:
Length: 87mm (3.4")
Width: 60mm (2.4")
Height: 10mm (0.39")

This is a great addition to the product currently being discussed.

Front Axles (2) (R & S)

This is a Pair of Stock Replacement Front Axles for the Rustler and Stampede.
These are situated in the front steering blocks.

FEATURES:
Steel construction
Natural color

INCLUDES:
2 front axles

NEEDS:
Absolutely nothing. These are direct replacement parts.

SPECS:
Length: 32mm (1.26")
Size: 5mm

COMMENTS:
These will not work for the nitro variations. For that axle, use
    TRAC2536.

This product is often purchased with the above pointed out product.

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Strong Driveshaft Assembly for the Slash 4x4 from Traxxas

FUNCTIONS:
Black plastic and steel construction

INCLUDES:
Rear driveshaft assembly
Screw pin

NEEDS:
Installation on automobile

This product compliments the main item right here.

30T Idler Gear Steel

This is the optional Steel Idler Equipment for lots of Traxxas Vehicles.

FEATURES:
Steel construction

INCLUDES:
One steel 30T idler equipment

NEEDS:
Installation on automobile

Many others have purchased this product along with the product that you are currently reviewing.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel construction
_
Roll pin pre-installed

INCLUDES:
One slipper clutch set

SPECIFICATIONS:
Length: 1.98" (50mm)
Size: .21" ( 5mm)

COMMENTS:
This part will fit both the requirement and XL variation of the Rustler
or Stampede.