Traxxas Box, Receiver For Stmpd, Rstlr, Bandt

This is the Receiver Box for use on the
Traxxas Stampede, Rustler, and Outlaw Vehicles.

FEATURES:
Nylon building and construction
Black in color

INCLUDES:
One Receiver Box
One Rubber Seal
Foam Cushioning
2 2.5x8mm Cap Head Screws
2 3x10mm Cap Head Screws
2 2.5x10mm Cap Head Screws
One Tube of Grease
Direction sheet

REQUIRES:
Installation on the car

SPECIFICATIONS:
Length: 78mm (3.07")
Width: 35mm (1.4")
Height: 33mm (1.3")

This thing compliments the main item here.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building and construction
Blue rubber dirt guards

INCLUDES:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside diameter: 3/16" (5mm)
Outdoors diameter: 7/16" (11mm)
Width: 5/32" (4mm)

Get this thing to improve the one you are reading around.

Hc Connector M/F (1) Available Only From

This is the Male/Female Traxxas Connectors Plugs Just (No Wires).

FUNCTIONS:
Shrouded wire connections (no diminish tube required)
Wide area, gold-plated terminals
Reverse polarity security makes it difficult to link backwards
Textured surface for easy gripping
Compatible with high-current 12-gauge wire
Secure, positive locking spring loaded terminals for constant
    contact
Numerous locking barbs keep terminals protect

INCLUDES:
One black female plastic port
One black male plastic port
2 sets of gold metal pins
Direction sheet

REQUIRES:
Soldering wires to the metal pins

The listed below thing likewise pairs actually well with the thing being reviewed.

Mounting Plate For Stampede Esc

This is the ESC and Receiver Box Mounting Plate for use on the
Traxxas Stampede.

FEATURES:
Nylon building and construction
Black in color

INCLUDES:
One Mounting Plate
Four 3x7.5mm Flanged Button Head Screws
2 3x12mm Flanged Button Head Screws

REQUIRES:
Installation on the car

SPECIFICATIONS:
Length: 87mm (3.4")
Width: 60mm (2.4")
Height: 10mm (0.39")

This is a fantastic enhancement to the thing currently being reviewed.

Front Axles (2) (R & S)

This is a Set of Stock Replacement Front Axles for the Rustler and Stampede.
These are situated in the front steering blocks.

FEATURES:
Steel building and construction
Natural color

INCLUDES:
2 front axles

REQUIRES:
Nothing. These are direct replacement parts.

SPECS:
Length: 32mm (1.26")
Size: 5mm

COMMENTS:
These will not work for the nitro variations. For that axle, use
    TRAC2536.

This thing is regularly bought with the above stated thing.

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Heavy Duty Driveshaft Assembly for the Slash 4x4 from Traxxas

FUNCTIONS:
Black plastic and steel building and construction

INCLUDES:
Rear driveshaft assembly
Screw pin

REQUIRES:
Installation on car

This thing compliments the main item here.

30T Idler Gear Steel

This is the optional Steel Idler Equipment for lots of Traxxas Vehicles.

FEATURES:
Steel building and construction

INCLUDES:
One steel 30T idler gear

REQUIRES:
Installation on car

Lots of others have bought this thing along with the thing that you are currently reading about.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel building and construction
_
Roll pin pre-installed

INCLUDES:
One slipper clutch set

SPECIFICATIONS:
Length: 1.98" (50mm)
Size: .21" ( 5mm)

COMMENTS:
This part will fit both the requirement and XL variation of the Rustler
or Stampede.