Traxxas Box, Receiver For Stmpd, Rstlr, Bandt

This is the Receiver Box for usage on the
Traxxas Stampede, Rustler, and Bandit Vehicles.

FEATURES:
Nylon construction
Black in color

CONSISTS OF:
One Receiver Box
One Rubber Seal
Foam Cushioning
2 2.5x8mm Cap Head Screws
2 3x10mm Cap Head Screws
2 2.5x10mm Cap Head Screws
One Tube of Grease
Guideline sheet

REQUIRES:
Installation on the vehicle

SPECS:
Length: 78mm (3.07")
Width: 35mm (1.4")
Height: 33mm (1.3")

This thing praises the main item right here.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing construction
Blue rubber dirt guards

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside size: 3/16" (5mm)
Outdoors size: 7/16" (11mm)
Width: 5/32" (4mm)

Get this thing to boost the one you are reading about.

Hc Connector M/F (1) Available Only From

This is the Male/Female Traxxas Connectors Plugs Only (No Wires).

FUNCTIONS:
Shrouded wire connections (no shrink tube needed)
Wide area, gold-plated terminals
Reverse polarity security makes it difficult to link backwards
Textured surface for simple gripping
Compatible with high-current 12-gauge wire
Protect, positive locking spring crammed terminals for constant
    contact
Several locking barbs keep terminals secure

CONSISTS OF:
One black female plastic connector
One black male plastic connector
2 sets of gold metal pins
Guideline sheet

REQUIRES:
Soldering wires to the metal pins

The below thing likewise pairs really well with the thing being gone over.

Mounting Plate For Stampede Esc

This is the ESC and Receiver Box Mounting Plate for usage on the
Traxxas Stampede.

FEATURES:
Nylon construction
Black in color

CONSISTS OF:
One Mounting Plate
4 3x7.5mm Flanged Button Head Screws
2 3x12mm Flanged Button Head Screws

REQUIRES:
Installation on the vehicle

SPECS:
Length: 87mm (3.4")
Width: 60mm (2.4")
Height: 10mm (0.39")

This is a superb enhancement to the thing currently being gone over.

Front Axles (2) (R & S)

This is a Set of Stock Replacement Front Axles for the Rustler and Stampede.
These are situated in the front steering blocks.

FEATURES:
Steel construction
Natural color

CONSISTS OF:
2 front axles

REQUIRES:
Nothing. These are direct replacement parts.

SPECS:
Length: 32mm (1.26")
Size: 5mm

COMMENTS:
These will not work for the nitro versions. For that axle, usage
    TRAC2536.

This thing is regularly purchased with the above discussed thing.

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Sturdy Driveshaft Assembly for the Slash 4x4 from Traxxas

FUNCTIONS:
Black plastic and steel construction

CONSISTS OF:
Rear driveshaft assembly
Screw pin

REQUIRES:
Installation on vehicle

This thing praises the main item right here.

30T Idler Gear Steel

This is the optional Steel Idler Equipment for lots of Traxxas Vehicles.

FEATURES:
Steel construction

CONSISTS OF:
One steel 30T idler equipment

REQUIRES:
Installation on vehicle

Lots of others have actually purchased this thing together with the thing that you are currently checking out.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel construction
_
Roll pin pre-installed

CONSISTS OF:
One slipper clutch set

SPECS:
Length: 1.98" (50mm)
Size: .21" ( 5mm)

COMMENTS:
This part will fit both the requirement and XL variation of the Rustler
or Stampede.