Traxxas Box, Receiver For Stmpd, Rstlr, Bandt

This is the Receiver Box for use on the
Traxxas Stampede, Rustler, and Outlaw Vehicles.

FEATURES:
Nylon construction
Black in color

INCLUDES:
One Receiver Box
One Rubber Seal
Foam Cushioning
Two 2.5x8mm Cap Head Screws
Two 3x10mm Cap Head Screws
Two 2.5x10mm Cap Head Screws
One Tube of Grease
Instruction sheet

NEEDS:
Setup on the automobile

SPECIFICATIONS:
Length: 78mm (3.07")
Width: 35mm (1.4")
Height: 33mm (1.3")

This thing compliments the main item below.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing construction
Blue rubber dirt guards

INCLUDES:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside size: 3/16" (5mm)
Outside size: 7/16" (11mm)
Width: 5/32" (4mm)

Get this thing to boost the one you are reading around.

Hc Connector M/F (1) Available Only From

This is the Male/Female Traxxas Connectors Plugs Only (No Wires).

FEATURES:
Shrouded wire connections (no shrink tube needed)
Wide surface area, gold-plated terminals
Reverse polarity security makes it impossible to connect in reverse
Textured surface area for simple gripping
Compatible with high-current 12-gauge wire
Secure, positive locking spring loaded terminals for consistent
    contact
Several locking barbs keep terminals secure

INCLUDES:
One black female plastic port
One black male plastic port
Two sets of gold metal pins
Instruction sheet

NEEDS:
Soldering wires to the metal pins

The below thing additionally pairs actually well with the thing being talked about.

Mounting Plate For Stampede Esc

This is the ESC and Receiver Box Mounting Plate for use on the
Traxxas Stampede.

FEATURES:
Nylon construction
Black in color

INCLUDES:
One Mounting Plate
4 3x7.5mm Flanged Button Head Screws
Two 3x12mm Flanged Button Head Screws

NEEDS:
Setup on the automobile

SPECIFICATIONS:
Length: 87mm (3.4")
Width: 60mm (2.4")
Height: 10mm (0.39")

This is a fantastic addition to the thing presently being talked about.

Front Axles (2) (R & S)

This is a Pair of Stock Replacement Front Axles for the Rustler and Stampede.
These are situated in the front steering blocks.

FEATURES:
Steel construction
Natural color

INCLUDES:
Two front axles

NEEDS:
Nothing. These are direct replacement parts.

SPECS:
Length: 32mm (1.26")
Size: 5mm

REMARKS:
These will not work for the nitro variations. For that axle, use
    TRAC2536.

This thing is regularly bought with the above discussed thing.

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Heavy Duty Driveshaft Assembly for the Slash 4x4 from Traxxas

FEATURES:
Black plastic and steel construction

INCLUDES:
Rear driveshaft assembly
Screw pin

NEEDS:
Setup on automobile

This thing compliments the main item below.

30T Idler Gear Steel

This is the optional Steel Idler Equipment for numerous Traxxas Vehicles.

FEATURES:
Steel construction

INCLUDES:
One steel 30T idler equipment

NEEDS:
Setup on automobile

Lots of others have actually bought this thing in addition to the thing that you are presently reviewing.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel construction
_
Roll pin pre-installed

INCLUDES:
One slipper clutch set

SPECIFICATIONS:
Length: 1.98" (50mm)
Size: .21" ( 5mm)

REMARKS:
This part will fit both the standard and XL variation of the Rustler
or Stampede.