Traxxas Box, Receiver For Stmpd, Rstlr, Bandt

This is the Receiver Box for usage on the
Traxxas Stampede, Rustler, and Bandit Vehicles.

FEATURES:
Nylon construction
Black in color

CONSISTS OF:
One Receiver Box
One Rubber Seal
Foam Padding
2 2.5x8mm Cap Head Screws
2 3x10mm Cap Head Screws
2 2.5x10mm Cap Head Screws
One Tube of Grease
Instruction sheet

NEEDS:
Installation on the vehicle

SPECIFICATIONS:
Length: 78mm (3.07")
Width: 35mm (1.4")
Height: 33mm (1.3")

This product compliments the main item below.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing construction
Blue rubber dirt shields

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside size: 3/16" (5mm)
Outside size: 7/16" (11mm)
Width: 5/32" (4mm)

Get this product to enhance the one you read about.

Hc Connector M/F (1) Available Only From

This is the Male/Female Traxxas Connectors Plugs Only (No Wires).

FEATURES:
Shrouded wire connections (no shrink tube needed)
Wide surface area, gold-plated terminals
Reverse polarity security makes it impossible to link backwards
Textured surface for simple gripping
Suitable with high-current 12-gauge wire
Protect, positive locking spring crammed terminals for constant
    contact
Several locking barbs keep terminals secure

CONSISTS OF:
One black female plastic connector
One black male plastic connector
2 sets of gold metal pins
Instruction sheet

NEEDS:
Soldering wires to the metal pins

The listed below product likewise pairs actually well with the product being talked about.

Mounting Plate For Stampede Esc

This is the ESC and Receiver Box Mounting Plate for usage on the
Traxxas Stampede.

FEATURES:
Nylon construction
Black in color

CONSISTS OF:
One Mounting Plate
4 3x7.5mm Flanged Button Head Screws
2 3x12mm Flanged Button Head Screws

NEEDS:
Installation on the vehicle

SPECIFICATIONS:
Length: 87mm (3.4")
Width: 60mm (2.4")
Height: 10mm (0.39")

This is a wonderful addition to the product presently being talked about.

Front Axles (2) (R & S)

This is a Set of Stock Replacement Front Axles for the Rustler and Stampede.
These are situated in the front steering blocks.

FEATURES:
Steel construction
Natural color

CONSISTS OF:
2 front axles

NEEDS:
Nothing. These are direct replacement parts.

SPECS:
Length: 32mm (1.26")
Diameter: 5mm

REMARKS:
These will not work for the nitro variations. For that axle, usage
    TRAC2536.

This product is often gotten with the above pointed out product.

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Sturdy Driveshaft Assembly for the Slash 4x4 from Traxxas

FEATURES:
Black plastic and steel construction

CONSISTS OF:
Rear driveshaft assembly
Screw pin

NEEDS:
Installation on vehicle

This product compliments the main item below.

30T Idler Gear Steel

This is the optional Steel Idler Equipment for lots of Traxxas Vehicles.

FEATURES:
Steel construction

CONSISTS OF:
One steel 30T idler equipment

NEEDS:
Installation on vehicle

Numerous others have gotten this product together with the product that you are presently checking out.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel construction
_
Roll pin pre-installed

CONSISTS OF:
One slipper clutch set

SPECIFICATIONS:
Length: 1.98" (50mm)
Diameter: .21" ( 5mm)

REMARKS:
This part will fit both the standard and XL variation of the Rustler
or Stampede.