Traxxas Box, Receiver For Stmpd, Rstlr, Bandt

This is the Receiver Box for usage on the
Traxxas Stampede, Rustler, and Outlaw Vehicles.

FEATURES:
Nylon construction
Black in color

INCLUDES:
One Receiver Box
One Rubber Seal
Foam Cushioning
Two 2.5x8mm Cap Head Screws
Two 3x10mm Cap Head Screws
Two 2.5x10mm Cap Head Screws
One Tube of Grease
Instruction sheet

REQUIRES:
Installation on the vehicle

SPECIFICATIONS:
Length: 78mm (3.07")
Width: 35mm (1.4")
Height: 33mm (1.3")

This thing praises the main item here.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing construction
Blue rubber dirt shields

INCLUDES:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside diameter: 3/16" (5mm)
Outside diameter: 7/16" (11mm)
Width: 5/32" (4mm)

Get this thing to boost the one you are reading about.

Hc Connector M/F (1) Available Only From

This is the Male/Female Traxxas Connectors Plugs Just (No Wires).

FUNCTIONS:
Shrouded wire connections (no diminish tube required)
Wide area, gold-plated terminals
Reverse polarity security makes it difficult to connect backwards
Textured surface for simple gripping
Compatible with high-current 12-gauge wire
Protect, positive locking spring loaded terminals for constant
    contact
Several locking barbs keep terminals secure

INCLUDES:
One black female plastic port
One black male plastic port
Two sets of gold metal pins
Instruction sheet

REQUIRES:
Soldering wires to the metal pins

The below thing also pairs truly well with the thing being gone over.

Mounting Plate For Stampede Esc

This is the ESC and Receiver Box Mounting Plate for usage on the
Traxxas Stampede.

FEATURES:
Nylon construction
Black in color

INCLUDES:
One Installing Plate
Four 3x7.5mm Flanged Button Head Screws
Two 3x12mm Flanged Button Head Screws

REQUIRES:
Installation on the vehicle

SPECIFICATIONS:
Length: 87mm (3.4")
Width: 60mm (2.4")
Height: 10mm (0.39")

This is a fantastic enhancement to the thing presently being gone over.

Front Axles (2) (R & S)

This is a Pair of Stock Replacement Front Axles for the Rustler and Stampede.
These are situated in the front steering blocks.

FEATURES:
Steel construction
Natural color

INCLUDES:
Two front axles

REQUIRES:
Absolutely nothing. These are direct replacement parts.

SPECS:
Length: 32mm (1.26")
Diameter: 5mm

REMARKS:
These will not work for the nitro versions. For that axle, usage
    TRAC2536.

This thing is frequently gotten with the above stated thing.

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Strong Driveshaft Assembly for the Slash 4x4 from Traxxas

FUNCTIONS:
Black plastic and steel construction

INCLUDES:
Rear driveshaft assembly
Screw pin

REQUIRES:
Installation on vehicle

This thing praises the main item here.

30T Idler Gear Steel

This is the optional Steel Idler Equipment for numerous Traxxas Vehicles.

FEATURES:
Steel construction

INCLUDES:
One steel 30T idler gear

REQUIRES:
Installation on vehicle

Numerous others have gotten this thing in addition to the thing that you are presently reading about.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel construction
_
Roll pin pre-installed

INCLUDES:
One slipper clutch set

SPECIFICATIONS:
Length: 1.98" (50mm)
Diameter: .21" ( 5mm)

REMARKS:
This part will fit both the requirement and XL variation of the Rustler
or Stampede.