Traxxas Box, Receiver For Stmpd, Rstlr, Bandt

This is the Receiver Box for usage on the
Traxxas Stampede, Rustler, and Bandit Vehicles.

FEATURES:
Nylon construction
Black in color

CONSISTS OF:
One Receiver Box
One Rubber Seal
Foam Padding
2 2.5x8mm Cap Head Screws
2 3x10mm Cap Head Screws
2 2.5x10mm Cap Head Screws
One Tube of Grease
Guideline sheet

NEEDS:
Installation on the vehicle

SPECS:
Length: 78mm (3.07")
Width: 35mm (1.4")
Height: 33mm (1.3")

This thing praises the main item right here.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing construction
Blue rubber dirt shields

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside diameter: 3/16" (5mm)
Outdoors diameter: 7/16" (11mm)
Width: 5/32" (4mm)

Get this thing to improve the one you read about.

Hc Connector M/F (1) Available Only From

This is the Male/Female Traxxas Connectors Plugs Only (No Wires).

FEATURES:
Shrouded wire connections (no diminish tube needed)
Wide surface area, gold-plated terminals
Reverse polarity protection makes it difficult to link in reverse
Textured surface for simple gripping
Compatible with high-current 12-gauge wire
Protect, positive locking spring crammed terminals for consistent
    contact
Numerous locking barbs keep terminals secure

CONSISTS OF:
One black female plastic adapter
One black male plastic adapter
2 sets of gold metal pins
Guideline sheet

NEEDS:
Soldering wires to the metal pins

The listed below thing likewise pairs really well with the thing being gone over.

Mounting Plate For Stampede Esc

This is the ESC and Receiver Box Mounting Plate for usage on the
Traxxas Stampede.

FEATURES:
Nylon construction
Black in color

CONSISTS OF:
One Installing Plate
4 3x7.5mm Flanged Button Head Screws
2 3x12mm Flanged Button Head Screws

NEEDS:
Installation on the vehicle

SPECS:
Length: 87mm (3.4")
Width: 60mm (2.4")
Height: 10mm (0.39")

This is a wonderful enhancement to the thing presently being gone over.

Front Axles (2) (R & S)

This is a Pair of Stock Replacement Front Axles for the Rustler and Stampede.
These are situated in the front steering blocks.

FEATURES:
Steel construction
Natural color

CONSISTS OF:
2 front axles

NEEDS:
Nothing. These are direct replacement parts.

SPECS:
Length: 32mm (1.26")
Diameter: 5mm

REMARKS:
These will not work for the nitro variations. For that axle, usage
    TRAC2536.

This thing is frequently gotten with the above stated thing.

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Sturdy Driveshaft Assembly for the Slash 4x4 from Traxxas

FEATURES:
Black plastic and steel construction

CONSISTS OF:
Rear driveshaft assembly
Screw pin

NEEDS:
Installation on vehicle

This thing praises the main item right here.

30T Idler Gear Steel

This is the optional Steel Idler Equipment for numerous Traxxas Vehicles.

FEATURES:
Steel construction

CONSISTS OF:
One steel 30T idler equipment

NEEDS:
Installation on vehicle

Many others have actually gotten this thing together with the thing that you are presently reading about.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel construction
_
Roll pin pre-installed

CONSISTS OF:
One slipper clutch set

SPECS:
Length: 1.98" (50mm)
Diameter: .21" ( 5mm)

REMARKS:
This part will fit both the requirement and XL version of the Rustler
or Stampede.