Traxxas Box, Receiver For Stmpd, Rstlr, Bandt

This is the Receiver Box for usage on the
Traxxas Stampede, Rustler, and Bandit Vehicles.

FEATURES:
Nylon construction
Black in color

CONSISTS OF:
One Receiver Box
One Rubber Seal
Foam Cushioning
2 2.5x8mm Cap Head Screws
2 3x10mm Cap Head Screws
2 2.5x10mm Cap Head Screws
One Tube of Grease
Instruction sheet

REQUIRES:
Setup on the vehicle

SPECIFICATIONS:
Length: 78mm (3.07")
Width: 35mm (1.4")
Height: 33mm (1.3")

This product compliments the main item here.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing construction
Blue rubber dirt guards

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside diameter: 3/16" (5mm)
Outdoors diameter: 7/16" (11mm)
Width: 5/32" (4mm)

Get this product to enhance the one you are reading about.

Hc Connector M/F (1) Available Only From

This is the Male/Female Traxxas Connectors Plugs Only (No Wires).

FUNCTIONS:
Shrouded wire connections (no diminish tube required)
Wide surface area, gold-plated terminals
Reverse polarity security makes it difficult to connect in reverse
Textured surface for simple gripping
Suitable with high-current 12-gauge wire
Secure, favorable locking spring loaded terminals for constant
    contact
Numerous locking barbs keep terminals secure

CONSISTS OF:
One black female plastic adapter
One black male plastic adapter
2 sets of gold metal pins
Instruction sheet

REQUIRES:
Soldering wires to the metal pins

The below product also pairs truly well with the product being gone over.

Mounting Plate For Stampede Esc

This is the ESC and Receiver Box Mounting Plate for usage on the
Traxxas Stampede.

FEATURES:
Nylon construction
Black in color

CONSISTS OF:
One Installing Plate
Four 3x7.5mm Flanged Button Head Screws
2 3x12mm Flanged Button Head Screws

REQUIRES:
Setup on the vehicle

SPECIFICATIONS:
Length: 87mm (3.4")
Width: 60mm (2.4")
Height: 10mm (0.39")

This is a superb addition to the product presently being gone over.

Front Axles (2) (R & S)

This is a Set of Stock Replacement Front Axles for the Rustler and Stampede.
These are situated in the front steering blocks.

FEATURES:
Steel construction
Natural color

CONSISTS OF:
2 front axles

REQUIRES:
Nothing. These are direct replacement parts.

SPECS:
Length: 32mm (1.26")
Diameter: 5mm

REMARKS:
These will not work for the nitro versions. For that axle, usage
    TRAC2536.

This product is often gotten with the above pointed out product.

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Heavy Duty Driveshaft Assembly for the Slash 4x4 from Traxxas

FUNCTIONS:
Black plastic and steel construction

CONSISTS OF:
Rear driveshaft assembly
Screw pin

REQUIRES:
Setup on vehicle

This product compliments the main item here.

30T Idler Gear Steel

This is the optional Steel Idler Equipment for many Traxxas Vehicles.

FEATURES:
Steel construction

CONSISTS OF:
One steel 30T idler gear

REQUIRES:
Setup on vehicle

Many others have gotten this product along with the product that you are presently checking out.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel construction
_
Roll pin pre-installed

CONSISTS OF:
One slipper clutch set

SPECIFICATIONS:
Length: 1.98" (50mm)
Diameter: .21" ( 5mm)

REMARKS:
This part will fit both the standard and XL version of the Rustler
or Stampede.