Traxxas Axle Carriers Use Larger 6 X 1

These are the Optional Axle Carriers L & R for
use on the Traxxas Revo series.

FEATURES:
Nylon Building
Black in Color
Permits Oversized Bearing utilize

CONSISTS OF:
One Left Axle Carrier
One Right Axle Carrier
Four Dust Boot Retainers
2 Bearing Spacers

REQUIRES:
Setup

Here is a fantastic product that many others have purchased the exact same time.

Pivot Ball Caps & Dust Boots

This is the replacement Pivot Ball and Dust Cap Boot Set
    for the Traxxas Revo, E-Revo and T-Maxx 3.3 vehicles.

FEATURES:
Nylon and Rubber Building
Blue and Black in Color

CONSISTS OF:
Four Blue Rubber Pivot Ball Boots
Four Black Dust Boot Retainer
Four Blue Notched Dust Boot Retainer
Four Blue Rubber Boot Plugs
Four nylon Pivot Ball Retainers
Instruction sheet

REQUIRES:
2 plans needed to finish truck

Get this product to enhance the one you read about.

12 X 18 X 4Mm Ball Bearing (2) Blue Rubber Sheild Revo

    These are the replacement Wheel Hub Ball Bearings for
the Traxxas Nitro Revo Beast Truck.

FEATURES:
Stainless-steel Building
Blue Rubber Sealed

CONSISTS OF:
2 12mm x 18mm Blue Sealed Stainless Wheel Hub Bearings

REQUIRES:
Assembly onto Vehicle

SPECIFICATIONS:
Outer Size: 18mm (0.70")
Inner Size: 12mm (0.47")
Density: 4mm (0.15")

COMMENTS:
These are for the Inside of the Wheel Hubs, the Truck Requires
Four Overall of these Bearings.

Get this product to enhance the one you read about.

Bbs Blue Rubber Sealed 6 X 13M

This is a set of Traxxas 6x13x5mm Ball Bearings
for use on the E-Revo

FEATURES:
Stainless-steel bearing building
Blue rubber dirt guards

CONSISTS OF:
(2) 6x13x5mm ball bearings Part #5180

SPECIFICATIONS:
Inside size: 6mm (0.24")
Outdoors size: 13mm (0.51")
Width: 5mm (0.20")

Want one more fantastic product to compliment the above pointed out product?

Driveshaft Assembly (1)

This is the Driveshaft Assembly for the Traxxas Revo 3.3.
and the T-Maxx 3.3.

FEATURES:
Completely assembled
Plastic telescoping driveshaft with steel universals
Blue rubber boot guards telescoping areas from dirt
Connects to the differential with one screw pin
Works on the front or back, right or left of car

CONSISTS OF:
#5458X Yoke, TRAC9798
#5145 Screw Pin, TRAC5145
#5450 Halfshaft, TRAC7450
#5452 U Joint, TRAC7452
#5459 Rubber Boot, TRAC7459
Instruction sheet

REQUIRES:
Installing on chassis

Several others have bought this product together with the product that you are presently reading about.

Yokes Diff/Tranny

These are the Diff and Trans Drive Yokes for the Traxxas T-Maxx 3.3. TRAC78**

FEATURES:
Black plastic building

CONSISTS OF:
2 drive yokes
2 4x15mm Yoke pins

REQUIRES:
T-Maxx 3.3

SPECIFICATIONS:
Length: 15/16" (23mm)
Size: 3/4" (17mm)

The below product additionally sets truly well with the product being reviewed.

Pivot Balls W/Cap

These are the Pivot Balls and Pivot Ball Cap Bushings for the
Traxxas T-Maxx and E-Maxx 4WD Radio Control Beast Trucks.
Two of these pivot balls suit the axle providers at each wheel
    The pivot ball cap bushings fit between the pivot balls
and the aluminum caps.

FEATURES:
Changes stock pivot balls and pivot ball cap bushings.
Pivot balls are made of steel, pivot ball cap bushings are made of
    plastic.

INCLUDES:
Four pivot balls.
Four pivot ball cap bushings

REQUIRES:
Threading the pivot balls through the axle providers and into the
    suspension arms. Placing pivot ball cap bushings between the pivot
    balls and aluminum caps.