Traxxas Alum Slipper Pressure Plate & Hub Jato

These are the Slipper Press Plate and Center
for the Traxxas Nitro Jato Stadium Truck.

FEATURES:
Pot Metal Building and construction
Silver in Color

CONSISTS OF:
One Slipper Press Plate
One Slipper Press Plate Center

NEEDS:
Assembly onto Automobile

You will certainly enjoy this item if you have the item just above stated.

Rebuild Kit, Slipper Clutch (S

This is the Slipper Clutch Rebuild Kit for the Traxxas Slash 4x4 Vehicles.

FEATURES:
Steel building

CONSISTS OF:
One Steel Disc
3 Friction Pads
Two Springs
One 4mm Lock Nut
One 5mm Lock Nut
Guidelines

NEEDS:
Disassembly of slipper clutch

Want another fantastic item to match the above pointed out item?

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building
Blue rubber dirt guards

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside size: 3/16" (5mm)
Outside size: 7/16" (11mm)
Width: 5/32" (4mm)

Get this item to enhance the one you are reading about.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel building
_
Roll pin pre-installed

CONSISTS OF:
One slipper clutch set

SPECS:
Length: 1.98" (50mm)
Size: .21" ( 5mm)

COMMENTS:
This part will fit both the requirement and XL version of the Rustler
or Stampede.

This item praises the above gone over item.

Spur Gear (86T) 48P

This is a Traxxas 48P, 86T Spur Gear for models with
Torque Control Slipper Clutch.

FEATURES:
48 pitch
86 tooth
Designed for models with a slipper clutch.
Black plastic building

CONSISTS OF:
One spur gear

SPECS:
Pitch: 48
Tooth: 86

COMMENTS:
For this slipper clutch design there is likewise a 76T gear (TRAC4676),
    83T gear (TRAC4683) and 90T gear (TRAC4690).

This is a fantastic addition to the item presently being gone over.

3 X 6Mm Cap Hex Screws (6)

These are 3x5mm Backplate screws for the Traxxas 2.5 Engine.

FEATURES:
Black steel construction.

INCLUDES:
6 black steel cap head screws.

REQUIRES:
Assembly on coverplate.

SPECS:
Length: 5mm
Size: 3mm

COMMENTS:
These may likewise be referred to as coverplate screws.

Often gotten with the item that you are presently reviewing.

23T Pinion 48P

This is a 23 Tooth 48 Pitch Pinion Gear By Traxxas

FUNCTIONS:
Pinion gear with set screw, Silver in color

CONSISTS OF:
(1) 23 Tooth 48 Pitch Pinion Gear
(1) One 4mmx2mm set screw

NEEDS:
Setup

SPECS:
Outer Size: 14mm (9/16")
Inner Size: 11mm (7/16")

The below item also sets truly well with the item being gone over.

Teflon Washers 5 X 8Mm (20)

These are Replacement Washers from Traxxas.

FEATURES:
Black plastic construction.
Used on the axles and in the transmission.

INCLUDES:
(20) Washers

SPECS:
Size: 5x8mm
Thickness: 0.5mm

This item is often gotten with the above pointed out item.

Spur Gear (90T) 48P

This is a Traxxas 48P, 90T Spur Gear for models
with Torque Control Slipper Clutch.

FEATURES:
48 pitch
90 tooth
Designed for models with a slipper clutch
Black plastic building

CONSISTS OF:
One spur gear

SPECS:
Pitch: 48
Tooth: 90

COMMENTS:
For this slipper clutch design there is likewise a 76T gear (TRAC4676),
    83T gear (TRAC4683) and 86T gear (TRAC4686).