Traxxas Alum Slipper Pressure Plate & Hub Jato

These are the Slipper Press Plate and Center
for the Traxxas Nitro Jato Arena Truck.

FEATURES:
Pot Metal Construction
Silver in Color

CONSISTS OF:
One Slipper Press Plate
One Slipper Press Plate Center

NEEDS:
Assembly onto Vehicle

You will love this product if you have the product earlier stated.

Rebuild Kit, Slipper Clutch (S

This is the Slipper Clutch Rebuild Kit for the Traxxas Slash 4x4 Vehicles.

FEATURES:
Steel construction

CONSISTS OF:
One Steel Disc
Three Friction Pads
2 Springs
One 4mm Lock Nut
One 5mm Lock Nut
Directions

NEEDS:
Disassembly of slipper clutch

Want one more wonderful thing to match the above pointed out thing?

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing construction
Blue rubber dirt shields

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside diameter: 3/16" (5mm)
Outside diameter: 7/16" (11mm)
Width: 5/32" (4mm)

Get this thing to enhance the one you read around.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel construction
_
Roll pin pre-installed

CONSISTS OF:
One slipper clutch set

SPECIFICATIONS:
Length: 1.98" (50mm)
Diameter: .21" ( 5mm)

REMARKS:
This part will fit both the requirement and XL variation of the Rustler
or Stampede.

This thing praises the above discussed thing.

Spur Gear (86T) 48P

This is a Traxxas 48P, 86T Spur Gear for designs with
Torque Control Slipper Clutch.

FEATURES:
48 pitch
86 tooth
Developed for designs with a slipper clutch.
Black plastic construction

CONSISTS OF:
One spur gear

SPECIFICATIONS:
Pitch: 48
Tooth: 86

REMARKS:
For this slipper clutch design there is also a 76T gear (TRAC4676),
    83T gear (TRAC4683) and 90T gear (TRAC4690).

This is a wonderful enhancement to the thing presently being discussed.

3 X 6Mm Cap Hex Screws (6)

These are 3x5mm Backplate screws for the Traxxas 2.5 Engine.

FEATURES:
Black steel construction.

INCLUDES:
Six black steel cap head screws.

REQUIRES:
Assembly on coverplate.

SPECS:
Length: 5mm
Diameter: 3mm

REMARKS:
These might also be described as coverplate screws.

Frequently purchased with the thing that you are presently checking out.

23T Pinion 48P

This is a 23 Tooth 48 Pitch Pinion Gear By Traxxas

FUNCTIONS:
Pinion gear with set screw, Silver in color

CONSISTS OF:
(1) 23 Tooth 48 Pitch Pinion Gear
(1) One 4mmx2mm set screw

NEEDS:
Installation

SPECIFICATIONS:
Outer Diameter: 14mm (9/16")
Inner Diameter: 11mm (7/16")

The listed below thing also sets truly well with the thing being discussed.

Teflon Washers 5 X 8Mm (20)

These are Replacement Washers from Traxxas.

FEATURES:
Black plastic construction.
Used on the axles and in the transmission.

INCLUDES:
(20) Washers

SPECIFICATIONS:
Size: 5x8mm
Density: 0.5mm

This thing is often purchased with the above pointed out thing.

Spur Gear (90T) 48P

This is a Traxxas 48P, 90T Spur Gear for designs
with Torque Control Slipper Clutch.

FEATURES:
48 pitch
90 tooth
Developed for designs with a slipper clutch
Black plastic construction

CONSISTS OF:
One spur gear

SPECIFICATIONS:
Pitch: 48
Tooth: 90

REMARKS:
For this slipper clutch design there is also a 76T gear (TRAC4676),
    83T gear (TRAC4683) and 86T gear (TRAC4686).