Traxxas 8400Mah 11.1V 3-Cell 25C Lipo

This is the Traxxas Power Cell 11.1V 8400mAh 25C 3S LiPo Battery.

FEATURES:
Semi rigid building and construction does not require a difficult case and eliminates
    wire harness connectors that can loosen up and fail
Engineered specifically to fit Traxxas designs
12AWG multi hair wire is soldered straight to the LiPo cells
    getting rid of increased resistance from bullet connectors and
    accidental reversed polarity connections

SUCHES AS:
Traxxas Power Cell 11.1V 8400mAh 25C LiPo 3S Battery with High
    Existing Port and JST/XH Balance Plug

REQUIRES:
Balancer and LiPo compatible charger or LiPo charger with built-in
    balancer such as the Onyx 235, DTXP4235
LiPo charging bag

SPECS:
Configuration: 3S2P
Continuous Discharge: 25C (210A)
Max Burst Rate: 50C (420A)
Watt Hours: 93.24
Charge Rate: 1C (8.4A)
Max Charge Rate: 2C (16.8A)
Dimensions: 6.1 x 1.7 x 1.8" (155 x 44 x 45mm)
Weight: 21.7oz (615g)

REMARKS:
ALWAYS use a LiPo-approved Battery charger
ALWAYS use a LiPo Cell Balancer
NEVER Charge over 4.20V per cell
NEVER Charge at currents greater than 1C
NEVER Charge through the "To ESC or "DISCHARGE" lead
NEVER EVER Trickle Charge
NEVER allow to Discharge below 2.5V per cell
NEVER dismantle or customize pack electrical wiring in any way or puncture cells
NEVER put on combustible products or leave ignored during
    charging
ALWAYS Charge in a fireproof place
ALWAYS set charger's output volts to match battery volts
ALWAYS keep out of reach of kids

The listed below product likewise sets really well with the product being gone over.

Adapter Traxxas ID LiPo Battery

This is the Traxxas iD LiPo Battery Adapter.

FEATURES:
Links Traxxas iD LiPo batteries to LiPo battery chargers with separate
    balance ports

SUCHES AS:
iD LiPo Battery Adapter with 3S Balance Port
Adapter with 2S Balance Port

SPECS:
Length: 5.2" (132mm) including connectors

This product praises the above gone over product.



This is the 2.4GHz Radio Controlled, Brushless Electric Powered,
Ready to Run Traxxas X-Maxx.

Ingenious New Features Include;

**Exclusive Self-Righting Action, if car rolls upside down**
**just push a button on the transmitter and in most cases**
**the X-Maxx will flip upright onto its wheels.**

**One handed body install and elimination system**
**eliminates body posts and pins.**

**Battery Retention System eliminates body clips or hook and loop straps**

**Shock towers also work as carrying deals with and level supports**
    **when car is put upside down for upkeep.**

**Additional Technical Details Will Be Added When It Appears.**

FUNCTIONS:
Traxxas Stability Management (TSM): Superior tuning algorithms operate on
    high-speed electronic parts to manage wheel spin and steering
    direction on loose dirt, concrete and even ice and snow. TSM can be
    great tuned or shut off by adjusting the multi-function knob on
    the TQi transmitter or the slider in the Traxxas Link app
Chassis: Composite nylon tub, modular design offers simple access
    to important parts, lower front and rear skids and integrated
    nerf bars for front, rear and side effect protection
Drive 4 wheel shaft drive, high-strength steel CV driveshafts with
    splined wheel hexes that get rid of axle pins, aluminum splined
    center driveshaft
Brushless Motor: Velineon 1600, 4 pole 1600Kv, 5mm shaft, aluminum
    heat sink
Motor Mount: Cradle design eliminates flexing, keyed pins lock equipment
    mesh in place
Radio: 2.4GHz TQi transmitter with 5-ch micro TSM telemetry ready
    receiver, BEC voltage and motor temperature sensors set up,
    self righting button, built-in fail safe,
    can be geared up with the TQi Docking Base along with the iPhone,
    iPad or iPod touch* to produce a graphical user interface for the
    car Traxxas Link TQi Wireless Module needed (not consisted of)
Steering Servo: High-torque with aluminum heat sink, double shear
    bearing supported servo horn
Electronic Speed Control: Velineon VXL-6s 6S LiPo compatible
Transmission; Single speed
Differentials: Sealed solidified steel bevel, oil filled, limited slip
Slipper Clutch: Double fan cooled
Battery Retention System: Integrated into chassis leading brace for
    greater rigidness, eliminates body clips or hook and loop straps,
    adjustable for different batteries
Body: ProGraphix painted and cut
Body Mount System: Quick one-hand body installation and elimination,
    rotating rear lock mechanism eliminates body posts and clips
Suspension: Captured high-strength steel pins, double sheer
    connections, adjustable roll center
Shocks: GTX aluminum bodied, oil-filled, integrated wiper seal keeps
    shafts clean reducing seal wear
Shock Towers: Composite plastic building and construction, also work as carrying
    deals with and level supports when car is put upside down
Tires: Aggressive all-terrain tread 8 x 4 x 4"
    foam inserts
Wheels: 4.3x5.7 inches (110x145mm), 17mm hexes
Steering: Bellcrank
Bumpers: Front and rear composite plastic with effect cushions
    behind each bumper to soften blows and contribute to toughness
Ball Bearings: Sealed, complete contact
Radio Box: Water resistant

SUCHES AS:
RTR X-Maxx Truck with Brushless Motor, Radio, ESC, Painted Body,
    Quick Start Guide and Upkeep Tools

REQUIRES:
Batteries: Two 3S LiPo 5000mAh or greater
Battery Battery charger: Suitable with picked LiPo batteries
AA Cells: For for transmitter
LiPo Charging Bag

SPECS:
Vehicle;
Length: 29.84" (758mm)
Front Track: 22.26" (540mm)
Rear Track: 20.66" (525mm) range from outer edges of wheels
    measured side-to-side
Ground Clearance: 4" (102mm)
Weight: 19.1pounds (8.66kg)
Trip Height: 13.79" (350mm)
Overall Drive Ratio: 8.24
Wheelbase: 18.92" (480mm)
Shock Length: 7.4" (187mm)
Battery Tray Dimensions: 7.7 x 2 x 1.7" (197mm x 51.5mm x 44mm)
    Body;
Length:
Width:
Height:

REMARKS:
Readily available in the following colors;
    Blue, TRAD75BB
    Red, TRAD75RR

For Replacement Ball Bearings usage:
    Qty. Size Place Qty. Bearing Set