Traxxas 3 X 6Mm Cap Hex Screws (6)

These are 3x5mm Backplate screws for the Traxxas 2.5 Engine.

FEATURES:
Black steel construction.

INCLUDES:
Six black steel cap head screws.

REQUIRES:
Assembly on coverplate.

SPECS:
Length: 5mm
Diameter: 3mm

REMARKS:
These might likewise be referred to as coverplate screws.

Often acquired with the product that you are presently reading about.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing construction
Blue rubber dirt shields

INCLUDES:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside size: 3/16" (5mm)
Outdoors size: 7/16" (11mm)
Width: 5/32" (4mm)

The listed below product likewise pairs truly well with the product being talked about.

Alum Slipper Pressure Plate & Hub Jato

These are the Slipper Press Plate and Hub
for the Traxxas Nitro Jato Arena Truck.

FEATURES:
Pot Metal Building and construction
Silver in Color

INCLUDES:
One Slipper Press Plate
One Slipper Press Plate Hub

REQUIRES:
Assembly onto Car

This is a fantastic addition to the product presently being talked about.

Rebuild Kit, Slipper Clutch (S

This is the Slipper Clutch Rebuild Set for the Traxxas Slash 4x4 Vehicles.

FEATURES:
Steel construction

INCLUDES:
One Steel Disc
3 Friction Pads
2 Springs
One 4mm Lock Nut
One 5mm Lock Nut
Instructions

REQUIRES:
Disassembly of slipper clutch

Numerous others have actually acquired this product together with the product that you are presently reading about.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel construction
_
Roll pin pre-installed

INCLUDES:
One slipper clutch set

SPECS:
Length: 1.98" (50mm)
Diameter: .21" ( 5mm)

REMARKS:
This part will fit both the requirement and XL variation of the Rustler
or Stampede.

Below is a great product that several others have actually purchased the exact same time.

Slipper Pressure Plate & Hub Revo

This is a Replacement Slipper Pressure Plate and Slipper Hub for the Revo.
These are part of the slipper assembly.

FEATURES:
Aluminum construction

INCLUDES:
One slipper pressure plate
One slipper center

REQUIRES:
Installation onto automobile.

You will certainly like this product if you have the product earlier mentioned.

Rebuild Kit Hd Slipper Clutch

This is the Sturdy Slipper Clutch Rebuild Set from Traxxas.

FEATURES:
Parts for both nitro and electrical Revo and Maxx trucks

INCLUDES:
3 Pads, steel Slipper Disc, two Locknuts, 2x9.8mm Pin, two
    Locknuts, Spring, two Spring Washers and Recommendations

REQUIRES:
Disassembly of slipper clutch

This product is regularly acquired with the above discussed product.

Spur Gear (90T) 48P

This is a Traxxas 48P, 90T Spur Gear for models
with Torque Control Slipper Clutch.

FEATURES:
48 pitch
90 tooth
Designed for models with a slipper clutch
Black plastic construction

INCLUDES:
One spur gear

SPECS:
Pitch: 48
Tooth: 90

REMARKS:
For this slipper clutch design there is likewise a 76T gear (TRAC4676),
    83T gear (TRAC4683) and 86T gear (TRAC4686).

Often acquired with the product that you are presently reading about.

3X8mm Screws Flat-Head (Hex Drive) (6)

These are the Traxxas Flathead 3 x 8mm Screws.

FEATURES:
Metal construction
Black in color

INCLUDES:
Six 3 x 8mm Flathead Hex Screws

REQUIRES:
Installation on the automobile

This is a fantastic addition to the product presently being talked about.

3 X 8Mm Counter Hex Screw (6)

These are 3x8mm Countersunk Hex Head Screws by Traxxas.
Can be used anywhere this kind of screw is needed.

FEATURES:
Metal Building and construction
Black in Color
Countersunk

INCLUDES:
(6) Screws

SPECS:
Length: 8mm
Diameter: 3mm