Traxxas 3 X 6Mm Cap Hex Screws (6)

These are 3x5mm Backplate screws for the Traxxas 2.5 Engine.

FEATURES:
Black steel construction.

INCLUDES:
Six black steel cap head screws.

REQUIRES:
Assembly on coverplate.

SPECS:
Length: 5mm
Diameter: 3mm

REMARKS:
These might also be described as coverplate screws.

Often gotten with the product that you are presently reviewing.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building
Blue rubber dirt shields

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside diameter: 3/16" (5mm)
Outdoors diameter: 7/16" (11mm)
Width: 5/32" (4mm)

The listed below product additionally pairs truly well with the product being reviewed.

Alum Slipper Pressure Plate & Hub Jato

These are the Slipper Press Plate and Hub
for the Traxxas Nitro Jato Arena Truck.

FEATURES:
Pot Metal Building
Silver in Color

CONSISTS OF:
One Slipper Press Plate
One Slipper Press Plate Hub

NEEDS:
Assembly onto Car

This is a amazing enhancement to the product presently being reviewed.

Rebuild Kit, Slipper Clutch (S

This is the Slipper Clutch Rebuild Set for the Traxxas Slash 4x4 Vehicles.

FEATURES:
Steel building

CONSISTS OF:
One Steel Disc
3 Friction Pads
Two Springs
One 4mm Lock Nut
One 5mm Lock Nut
Guidelines

NEEDS:
Disassembly of slipper clutch

Lots of others have gotten this product together with the product that you are presently reviewing.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel building
_
Roll pin pre-installed

CONSISTS OF:
One slipper clutch set

SPECS:
Length: 1.98" (50mm)
Diameter: .21" ( 5mm)

REMARKS:
This part will fit both the requirement and XL variation of the Rustler
or Stampede.

Below is a terrific product that numerous others have purchased the very same time.

Slipper Pressure Plate & Hub Revo

This is a Replacement Slipper Pressure Plate and Slipper Hub for the Revo.
These are part of the slipper assembly.

FEATURES:
Aluminum building

CONSISTS OF:
One slipper pressure plate
One slipper hub

NEEDS:
Installation onto vehicle.

You will enjoy this item if you have the item earlier discussed.

Rebuild Kit Hd Slipper Clutch

This is the Strong Slipper Clutch Rebuild Set from Traxxas.

FEATURES:
Components for both nitro and electric Revo and Maxx trucks

CONSISTS OF:
3 Pads, steel Slipper Disc, two Locknuts, 2x9.8mm Pin, two
    Locknuts, Spring, two Spring Washers and Instructions

NEEDS:
Disassembly of slipper clutch

This product is frequently gotten with the above discussed product.

Spur Gear (90T) 48P

This is a Traxxas 48P, 90T Spur Gear for designs
with Torque Control Slipper Clutch.

FEATURES:
48 pitch
90 tooth
Developed for designs with a slipper clutch
Black plastic building

CONSISTS OF:
One spur gear

SPECS:
Pitch: 48
Tooth: 90

REMARKS:
For this slipper clutch design there is also a 76T gear (TRAC4676),
    83T gear (TRAC4683) and 86T gear (TRAC4686).

Often gotten with the product that you are presently reviewing.

3X8mm Screws Flat-Head (Hex Drive) (6)

These are the Traxxas Flathead 3 x 8mm Screws.

FEATURES:
Metal building
Black in color

CONSISTS OF:
Six 3 x 8mm Flathead Hex Screws

NEEDS:
Installation on the vehicle

This is a amazing enhancement to the product presently being reviewed.

3 X 8Mm Counter Hex Screw (6)

These are 3x8mm Countersunk Hex Head Screws by Traxxas.
Can be used anywhere this kind of screw is needed.

FEATURES:
Metal Building
Black in Color
Countersunk

CONSISTS OF:
(6) Screws

SPECS:
Length: 8mm
Diameter: 3mm