Traxxas 3 X 6Mm Cap Hex Screws (6)

These are 3x5mm Backplate screws for the Traxxas 2.5 Engine.

FEATURES:
Black steel construction.

INCLUDES:
Six black steel cap head screws.

REQUIRES:
Assembly on coverplate.

SPECS:
Length: 5mm
Diameter: 3mm

REMARKS:
These may also be referred to as coverplate screws.

Often purchased with the thing that you are presently reviewing.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building
Blue rubber dirt guards

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside size: 3/16" (5mm)
Outdoors size: 7/16" (11mm)
Width: 5/32" (4mm)

The listed below thing additionally pairs actually well with the thing being talked about.

Alum Slipper Pressure Plate & Hub Jato

These are the Slipper Press Plate and Center
for the Traxxas Nitro Jato Stadium Truck.

FEATURES:
Pot Metal Building and construction
Silver in Color

CONSISTS OF:
One Slipper Press Plate
One Slipper Press Plate Center

NEEDS:
Assembly onto Car

This is a superb addition to the thing presently being talked about.

Rebuild Kit, Slipper Clutch (S

This is the Slipper Clutch Rebuild Set for the Traxxas Slash 4x4 Vehicles.

FEATURES:
Steel building

CONSISTS OF:
One Steel Disc
Three Friction Pads
Two Springs
One 4mm Lock Nut
One 5mm Lock Nut
Guidelines

NEEDS:
Disassembly of slipper clutch

Many others have actually purchased this thing together with the thing that you are presently reviewing.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel building
_
Roll pin pre-installed

CONSISTS OF:
One slipper clutch set

SPECS:
Length: 1.98" (50mm)
Diameter: .21" ( 5mm)

REMARKS:
This part will fit both the requirement and XL variation of the Rustler
or Stampede.

Below is a excellent thing that numerous others have actually purchased the exact same time.

Slipper Pressure Plate & Hub Revo

This is a Replacement Slipper Pressure Plate and Slipper Center for the Revo.
These are part of the slipper assembly.

FEATURES:
Aluminum building

CONSISTS OF:
One slipper pressure plate
One slipper hub

NEEDS:
Setup onto vehicle.

You will certainly like this thing if you have the thing just above discussed.

Rebuild Kit Hd Slipper Clutch

This is the Strong Slipper Clutch Rebuild Set from Traxxas.

FEATURES:
Elements for both nitro and electric Revo and Maxx trucks

CONSISTS OF:
Three Pads, steel Slipper Disc, two Locknuts, 2x9.8mm Pin, two
    Locknuts, Spring, two Spring Washers and Instructions

NEEDS:
Disassembly of slipper clutch

This thing is regularly purchased with the above mentioned thing.

Spur Gear (90T) 48P

This is a Traxxas 48P, 90T Spur Gear for designs
with Torque Control Slipper Clutch.

FEATURES:
48 pitch
90 tooth
Developed for designs with a slipper clutch
Black plastic building

CONSISTS OF:
One spur gear

SPECS:
Pitch: 48
Tooth: 90

REMARKS:
For this slipper clutch design there is also a 76T gear (TRAC4676),
    83T gear (TRAC4683) and 86T gear (TRAC4686).

Often purchased with the thing that you are presently reviewing.

3X8mm Screws Flat-Head (Hex Drive) (6)

These are the Traxxas Flathead 3 x 8mm Screws.

FEATURES:
Metal building
Black in color

CONSISTS OF:
Six 3 x 8mm Flathead Hex Screws

NEEDS:
Setup on the vehicle

This is a superb addition to the thing presently being talked about.

3 X 8Mm Counter Hex Screw (6)

These are 3x8mm Countersunk Hex Head Screws by Traxxas.
Can be utilized anywhere this type of screw is needed.

FEATURES:
Metal Building and construction
Black in Color
Countersunk

CONSISTS OF:
(6) Screws

SPECS:
Length: 8mm
Diameter: 3mm