Traxxas 54T 0.8 P Spur Gear

This is the 54 Tooth Spur Equipment
for the Traxxas Nitro Jato Stadium Truck.

FEATURES:
Nylon building and construction
Black in color
.8 Module pitch

INCLUDES:
One 54T 0.8 Pitch Spur Equipment

NEEDS:
Assembly onto automobile

Many others have actually purchased this item together with the item that you are presently reviewing.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building and construction
Blue rubber dirt guards

INCLUDES:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside diameter: 3/16" (5mm)
Outdoors diameter: 7/16" (11mm)
Width: 5/32" (4mm)

Below is a wonderful item that many others have actually purchased the same time.

Alum Bearing Adapter Slash 4X4

This is an optional Bearing Adapter for the Slash 4X4.

FUNCTIONS:
6061-T6 anodized blue aluminum building and construction
Steel 10x15x4mm ball bearing with blue rubber seal
Used on slipper shaft

INCLUDES:
One aluminum adapter
One 10x15x4mm ball bearing

NEEDS:
Installation on to slipper shaft
Remaining clutch pieces

You will certainly enjoy this product if you have the product earlier discussed.

10 X 15 X 4Mm Ball Bearing (2) Blue Rubber Sheild Revo

This is a set of 10x15mm Ball Bearings for usage on the Traxxas Revo.

FEATURES:
Steel Construction
Protected with blue rubber seals

INCLUDES:
2 Ball Bearings

NEEDS:
Assembly to automobile

SPECS:
Inner Size: 10mm
External Size: 15mm
Side Density: 4mm

REMARKS:
These bearings are used to support the Main Clutch (one needed).

This item praises the above discussed item.

13T Pinion Gear 32P

This is a 13 Tooth 32 Pitch Pinion Equipment for the Traxxas E-Maxx Truck.
This is the equipment which is connected straight to the motor.

FEATURES:
Machined Steel
Developed for a 3mm shaft

INCLUDES:
One 13 tooth Pinion Equipment
One 3 x 4mm Set Screw

NEEDS:
Assembly onto an E-Maxx truck.
1.5mm hex wrench to tighten set screw.

COMMENTS:
This equipment is just one of two which are used on the E-Maxx double motor
    set-up.

This item praises the above discussed item.

Rebuild Kit, Slipper Clutch (S

This is the Slipper Clutch Rebuild Package for the Traxxas Slash 4x4 Vehicles.

FEATURES:
Steel building and construction

INCLUDES:
One Steel Disc
3 Friction Pads
2 Springs
One 4mm Lock Nut
One 5mm Lock Nut
Directions

NEEDS:
Disassembly of slipper clutch

This is a wonderful enhancement to the item presently being discussed.

Input Shaft (Slipper Shaft)/ B

This is the Input Shaft for usage on the Traxxas Slash 4x4 Vehicles.

FEATURES:
Steel building and construction
Black in color

INCLUDES:
One Input Shaft
One Bearing Adapter
One Pin

NEEDS:
Installation on the automobile

SPECS:
Length: 58mm (2.3")

Below is an additional item that praises the item being discussed.

Driveshaft Assembly (1)

This is the Driveshaft Assembly for the Traxxas Revo 3.3.
and the T-Maxx 3.3.

FUNCTIONS:
Fully assembled
Plastic telescoping driveshaft with steel universals
Blue rubber boot guards telescoping areas from dirt
Connects to the differential with one screw pin
Functions on the front or back, right or left of automobile

INCLUDES:
#5458X Yoke, TRAC9798
#5145 Screw Pin, TRAC5145
#5450 Halfshaft, TRAC7450
#5452 U Joint, TRAC7452
#5459 Rubber Boot, TRAC7459
Guideline sheet

NEEDS:
Setting up on chassis