Traxxas 54T 0.8 P Spur Gear

This is the 54 Tooth Spur Gear
for the Traxxas Nitro Jato Arena Truck.

FEATURES:
Nylon building and construction
Black in color
.8 Module pitch

CONSISTS OF:
One 54T 0.8 Pitch Spur Gear

REQUIRES:
Assembly onto automobile

Many others have acquired this product along with the product that you are presently reviewing.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building and construction
Blue rubber dirt shields

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside size: 3/16" (5mm)
Outside size: 7/16" (11mm)
Width: 5/32" (4mm)

Below is a great product that several others have purchased the same time.

Alum Bearing Adapter Slash 4X4

This is an optional Bearing Adapter for the Slash 4X4.

FUNCTIONS:
6061-T6 anodized blue aluminum building and construction
Steel 10x15x4mm ball bearing with blue rubber seal
Used on slipper shaft

CONSISTS OF:
One aluminum adapter
One 10x15x4mm ball bearing

REQUIRES:
Setup on to slipper shaft
Remaining clutch pieces

You will certainly love this thing if you have the thing above stated.

10 X 15 X 4Mm Ball Bearing (2) Blue Rubber Sheild Revo

This is a set of 10x15mm Ball Bearings for usage on the Traxxas Revo.

FEATURES:
Steel Building
Protected with blue rubber seals

CONSISTS OF:
Two Ball Bearings

REQUIRES:
Assembly to automobile

SPECS:
Inner Diameter: 10mm
Outer Diameter: 15mm
Side Density: 4mm

REMARKS:
These bearings are used to support the Main Clutch (one needed).

This product praises the above discussed product.

13T Pinion Gear 32P

This is a 13 Tooth 32 Pitch Pinion Gear for the Traxxas E-Maxx Truck.
This is the equipment which is connected directly to the motor.

FEATURES:
Machined Steel
Designed for a 3mm shaft

CONSISTS OF:
One 13 tooth Pinion Gear
One 3 x 4mm Set Screw

REQUIRES:
Assembly onto an E-Maxx truck.
1.5mm hex wrench to tighten set screw.

COMMENTS:
This equipment is only one of two which are used on the E-Maxx dual motor
    set-up.

This product praises the above discussed product.

Rebuild Kit, Slipper Clutch (S

This is the Slipper Clutch Rebuild Kit for the Traxxas Slash 4x4 Vehicles.

FEATURES:
Steel building and construction

CONSISTS OF:
One Steel Disc
3 Friction Pads
Two Springs
One 4mm Lock Nut
One 5mm Lock Nut
Instructions

REQUIRES:
Disassembly of slipper clutch

This is a amazing addition to the product presently being discussed.

Input Shaft (Slipper Shaft)/ B

This is the Input Shaft for usage on the Traxxas Slash 4x4 Vehicles.

FEATURES:
Steel building and construction
Black in color

CONSISTS OF:
One Input Shaft
One Bearing Adapter
One Pin

REQUIRES:
Setup on the automobile

SPECS:
Length: 58mm (2.3")

Below is an additional product that praises the product being discussed.

Driveshaft Assembly (1)

This is the Driveshaft Assembly for the Traxxas Revo 3.3.
and the T-Maxx 3.3.

FUNCTIONS:
Totally put together
Plastic telescoping driveshaft with steel universals
Blue rubber boot shields telescoping areas from dirt
Connects to the differential with one screw pin
Works on the front or back, right or left of automobile

CONSISTS OF:
#5458X Yoke, TRAC9798
#5145 Screw Pin, TRAC5145
#5450 Halfshaft, TRAC7450
#5452 U Joint, TRAC7452
#5459 Rubber Boot, TRAC7459
Guideline sheet

REQUIRES:
Setting up on chassis