Traxxas 54T 0.8 P Spur Gear

This is the 54 Tooth Spur Gear
for the Traxxas Nitro Jato Arena Truck.

FEATURES:
Nylon construction
Black in color
.8 Module pitch

INCLUDES:
One 54T 0.8 Pitch Spur Gear

NEEDS:
Assembly onto vehicle

Numerous others have acquired this thing along with the thing that you are presently reading about.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing construction
Blue rubber dirt guards

INCLUDES:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside size: 3/16" (5mm)
Outdoors size: 7/16" (11mm)
Width: 5/32" (4mm)

Below is a wonderful thing that lots of others have bought at the exact same time.

Alum Bearing Adapter Slash 4X4

This is an optional Bearing Adapter for the Slash 4X4.

FUNCTIONS:
6061-T6 anodized blue aluminum construction
Steel 10x15x4mm ball bearing with blue rubber seal
Used on slipper shaft

INCLUDES:
One aluminum adapter
One 10x15x4mm ball bearing

NEEDS:
Installation on to slipper shaft
Staying clutch pieces

You will certainly enjoy this item if you have the item above mentioned.

10 X 15 X 4Mm Ball Bearing (2) Blue Rubber Sheild Revo

This is a set of 10x15mm Ball Bearings for usage on the Traxxas Revo.

FEATURES:
Steel Building and construction
Protected with blue rubber seals

INCLUDES:
2 Ball Bearings

NEEDS:
Assembly to vehicle

SPECIFICATIONS:
Inner Diameter: 10mm
External Diameter: 15mm
Side Thickness: 4mm

REMARKS:
These bearings are utilized to support the Primary Clutch (one required).

This thing compliments the above discussed thing.

13T Pinion Gear 32P

This is a 13 Tooth 32 Pitch Pinion Gear for the Traxxas E-Maxx Truck.
This is the gear which is attached directly to the motor.

FEATURES:
Machined Steel
Designed for a 3mm shaft

INCLUDES:
One 13 tooth Pinion Gear
One 3 x 4mm Set Screw

NEEDS:
Assembly onto an E-Maxx truck.
1.5mm hex wrench to tighten set screw.

COMMENTS:
This gear is just one of two which are utilized on the E-Maxx double motor
    set-up.

This thing compliments the above discussed thing.

Rebuild Kit, Slipper Clutch (S

This is the Slipper Clutch Rebuild Package for the Traxxas Slash 4x4 Vehicles.

FEATURES:
Steel construction

INCLUDES:
One Steel Disc
3 Friction Pads
2 Springs
One 4mm Lock Nut
One 5mm Lock Nut
Directions

NEEDS:
Disassembly of slipper clutch

This is a superb enhancement to the thing presently being discussed.

Input Shaft (Slipper Shaft)/ B

This is the Input Shaft for usage on the Traxxas Slash 4x4 Vehicles.

FEATURES:
Steel construction
Black in color

INCLUDES:
One Input Shaft
One Bearing Adapter
One Pin

NEEDS:
Installation on the vehicle

SPECIFICATIONS:
Length: 58mm (2.3")

Below is one more thing that compliments the thing being discussed.

Driveshaft Assembly (1)

This is the Driveshaft Assembly for the Traxxas Revo 3.3.
and the T-Maxx 3.3.

FUNCTIONS:
Totally assembled
Plastic telescoping driveshaft with steel universals
Blue rubber boot guards telescoping areas from dirt
Connects to the differential with one screw pin
Functions on the front or rear, right or left of vehicle

INCLUDES:
#5458X Yoke, TRAC9798
#5145 Screw Pin, TRAC5145
#5450 Halfshaft, TRAC7450
#5452 U Joint, TRAC7452
#5459 Rubber Boot, TRAC7459
Guideline sheet

NEEDS:
Installing on chassis