Traxxas 54T 0.8 P Spur Gear

This is the 54 Tooth Spur Gear
for the Traxxas Nitro Jato Arena Truck.

FEATURES:
Nylon building and construction
Black in color
.8 Module pitch

CONSISTS OF:
One 54T 0.8 Pitch Spur Gear

NEEDS:
Assembly onto car

Many others have actually bought this thing along with the thing that you are presently reading about.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building and construction
Blue rubber dirt guards

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside diameter: 3/16" (5mm)
Outdoors diameter: 7/16" (11mm)
Width: 5/32" (4mm)

Right here is a great thing that lots of others have actually bought at the very same time.

Alum Bearing Adapter Slash 4X4

This is an optional Bearing Adapter for the Slash 4X4.

FEATURES:
6061-T6 anodized blue aluminum building and construction
Steel 10x15x4mm ball bearing with blue rubber seal
Utilized on slipper shaft

CONSISTS OF:
One aluminum adapter
One 10x15x4mm ball bearing

NEEDS:
Setup on to slipper shaft
Staying clutch pieces

You will certainly like this item if you have the item just above stated.

10 X 15 X 4Mm Ball Bearing (2) Blue Rubber Sheild Revo

This is a set of 10x15mm Ball Bearings for use on the Traxxas Revo.

FEATURES:
Steel Building
Shielded with blue rubber seals

CONSISTS OF:
Two Ball Bearings

NEEDS:
Assembly to car

SPECS:
Inner Diameter: 10mm
Outer Diameter: 15mm
Side Thickness: 4mm

REMARKS:
These bearings are used to support the Primary Clutch (one required).

This thing praises the above gone over thing.

13T Pinion Gear 32P

This is a 13 Tooth 32 Pitch Pinion Gear for the Traxxas E-Maxx Truck.
This is the equipment which is connected straight to the motor.

FEATURES:
Machined Steel
Developed for a 3mm shaft

CONSISTS OF:
One 13 tooth Pinion Gear
One 3 x 4mm Set Screw

NEEDS:
Assembly onto an E-Maxx truck.
1.5mm hex wrench to tighten up set screw.

COMMENTS:
This equipment is just one of 2 which are used on the E-Maxx dual motor
    set-up.

This thing praises the above gone over thing.

Rebuild Kit, Slipper Clutch (S

This is the Slipper Clutch Rebuild Package for the Traxxas Slash 4x4 Vehicles.

FEATURES:
Steel building and construction

CONSISTS OF:
One Steel Disc
Three Friction Pads
Two Springs
One 4mm Lock Nut
One 5mm Lock Nut
Directions

NEEDS:
Disassembly of slipper clutch

This is a superb addition to the thing presently being gone over.

Input Shaft (Slipper Shaft)/ B

This is the Input Shaft for use on the Traxxas Slash 4x4 Vehicles.

FEATURES:
Steel building and construction
Black in color

CONSISTS OF:
One Input Shaft
One Bearing Adapter
One Pin

NEEDS:
Setup on the car

SPECS:
Length: 58mm (2.3")

Right here is an additional thing that praises the thing being gone over.

Driveshaft Assembly (1)

This is the Driveshaft Assembly for the Traxxas Revo 3.3.
and the T-Maxx 3.3.

FEATURES:
Totally put together
Plastic telescoping driveshaft with steel universals
Blue rubber boot guards telescoping sections from dirt
Connects to the differential with one screw pin
Functions on the front or rear, right or left of car

CONSISTS OF:
#5458X Yoke, TRAC9798
#5145 Screw Pin, TRAC5145
#5450 Halfshaft, TRAC7450
#5452 U Joint, TRAC7452
#5459 Rubber Boot, TRAC7459
Instruction sheet

NEEDS:
Setting up on chassis