Traxxas 5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing construction
Blue rubber dirt shields

INCLUDES:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside diameter: 3/16" (5mm)
Outside diameter: 7/16" (11mm)
Width: 5/32" (4mm)

Get this thing to improve the one you are reading around.

10 X 15 X 4Mm Ball Bearing (2) Blue Rubber Sheild Revo

This is a set of 10x15mm Ball Bearings for use on the Traxxas Revo.

FEATURES:
Steel Construction
Shielded with blue rubber seals

INCLUDES:
Two Ball Bearings

REQUIRES:
Assembly to automobile

SPECS:
Inner Size: 10mm
Outer Size: 15mm
Side Thickness: 4mm

COMMENTS:
These bearings are used to support the Main Clutch (one needed).

Regularly purchased with the thing that you are presently reviewing.

Teflon Washers 5 X 8Mm (20)

These are Replacement Washers from Traxxas.

FEATURES:
Black plastic construction.
Used on the axles and in the transmission.

INCLUDES:
(20) Washers

SPECS:
Size: 5x8mm
Thickness: 0.5mm

Regularly purchased with the thing that you are presently reviewing.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel construction
_
Roll pin pre-installed

INCLUDES:
One slipper clutch set

SPECS:
Length: 1.98" (50mm)
Size: .21" ( 5mm)

COMMENTS:
This part will fit both the requirement and XL variation of the Rustler
or Stampede.

This is a superb addition to the thing presently being discussed.

Front Bearing Carriers, For Slash 2Wd, Nitro Slash, E-Rustler &

These are Optional Front Bearing Carriers for the Traxxas Electric
Rustler, Stampede and Outlaw

The Front axles suit these bearing carriers.

FEATURES:
Black nylon construction

INCLUDES:
Two Front bearing (hub) providers
Two RPM decals

REQUIRES:
(4) 5x11mm bearings, if needed use (2) DTXC1547.

This is a superb addition to the thing presently being discussed.

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Strong Driveshaft Assembly for the Slash 4x4 from Traxxas

FUNCTIONS:
Black plastic and steel construction

INCLUDES:
Rear driveshaft assembly
Screw pin

REQUIRES:
Installation on automobile

You will certainly love this item if you have the item just above discussed.

30T Idler Gear Steel

This is the optional Steel Idler Equipment for lots of Traxxas Vehicles.

FEATURES:
Steel construction

INCLUDES:
One steel 30T idler equipment

REQUIRES:
Installation on automobile

This thing compliments the main item right here.

Steel Top Drive Gear 22T

This is the 22 tooth, hardened steel top drive equipment that fits numerous Traxxas
cars. .
Includes: 1 equipment only

You will certainly love this item if you have the item just above discussed.

Rear Bearing Carriers, For Traxxas Slash 2Wd, E-Rustler, E-Stamp

These are Optional Rear Bearing Carriers for the Traxxas Electric
Rustler, Stampede and Bandit.
The rear axles suit these bearing carriers.

FEATURES:
Black nylon construction

INCLUDES:
Two rear bearing (hub) providers
Two RPM decals

REQUIRES:
(4) 5x11mm bearings, if needed use (2) DTXC1547.

SPECS:
Height: 40mm (1.58")
Width at largest point: 15.4mm (0.61")

You will certainly love this item if you have the item just above discussed.

Planetary Gear Diff W/Steel Ring Gear Slash/Bandit /Stampe

This is the Complete Planetary Equipment Differential With Steel Ring Equipment
for the Traxxas Outlaw, Stampede and Rustler.

FEATURES:
Metal equipment shafts
Metal and plastic primary differential

INCLUDES:
Main differential with steel ring equipment
Planetary equipments and shafts
Sun equipments and shafts
Silicone grease

REQUIRES:
Installation on the automobile

COMMENTS:
For primary differential w/ steel ring - TRAC6380
World equipment shafts - TRAC6382
Silicon grease _- TRAC6037