Traxxas 5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building
Blue rubber dirt guards

INCLUDES:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside size: 3/16" (5mm)
Outdoors size: 7/16" (11mm)
Width: 5/32" (4mm)

Get this product to boost the one you read about.

10 X 15 X 4Mm Ball Bearing (2) Blue Rubber Sheild Revo

This is a set of 10x15mm Ball Bearings for use on the Traxxas Revo.

FEATURES:
Steel Building
Shielded with blue rubber seals

INCLUDES:
2 Ball Bearings

REQUIRES:
Assembly to car

SPECS:
Inner Diameter: 10mm
External Diameter: 15mm
Side Density: 4mm

REMARKS:
These bearings are utilized to support the Primary Clutch (one needed).

Frequently bought with the product that you are presently reviewing.

Teflon Washers 5 X 8Mm (20)

These are Replacement Washers from Traxxas.

FEATURES:
Black plastic construction.
Used on the axles and in the transmission.

INCLUDES:
(20) Washers

SPECS:
Size: 5x8mm
Density: 0.5mm

Frequently bought with the product that you are presently reviewing.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel building
_
Roll pin pre-installed

INCLUDES:
One slipper clutch set

SPECS:
Length: 1.98" (50mm)
Diameter: .21" ( 5mm)

REMARKS:
This part will fit both the requirement and XL version of the Rustler
or Stampede.

This is a wonderful enhancement to the product presently being talked about.

Front Bearing Carriers, For Slash 2Wd, Nitro Slash, E-Rustler &

These are Optional Front Bearing Providers for the Traxxas Electric
Rustler, Stampede and Outlaw

The Front axles suit these bearing carriers.

FEATURES:
Black nylon building

INCLUDES:
2 Front bearing (center) providers
2 RPM decals

REQUIRES:
(4) 5x11mm bearings, if needed use (2) DTXC1547.

This is a wonderful enhancement to the product presently being talked about.

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Sturdy Driveshaft Assembly for the Slash 4x4 from Traxxas

FEATURES:
Black plastic and steel building

INCLUDES:
Rear driveshaft assembly
Screw pin

REQUIRES:
Installation on car

You will certainly like this thing if you have the thing above discussed.

30T Idler Gear Steel

This is the optional Steel Idler Gear for numerous Traxxas Vehicles.

FEATURES:
Steel building

INCLUDES:
One steel 30T idler gear

REQUIRES:
Installation on car

This product praises the main item here.

Steel Top Drive Gear 22T

This is the 22 tooth, solidified steel leading drive gear that fits several Traxxas
automobiles. .
Consists of: 1 gear just

You will certainly like this thing if you have the thing above discussed.

Rear Bearing Carriers, For Traxxas Slash 2Wd, E-Rustler, E-Stamp

These are Optional Back Bearing Carriers for the Traxxas Electric
Rustler, Stampede and Bandit.
The rear axles suit these bearing carriers.

FEATURES:
Black nylon building

INCLUDES:
2 rear bearing (center) providers
2 RPM decals

REQUIRES:
(4) 5x11mm bearings, if needed use (2) DTXC1547.

SPECS:
Height: 40mm (1.58")
Width at largest point: 15.4mm (0.61")

You will certainly like this thing if you have the thing above discussed.

Planetary Gear Diff W/Steel Ring Gear Slash/Bandit /Stampe

This is the Complete Planetary Gear Differential With Steel Ring Gear
for the Traxxas Outlaw, Stampede and Rustler.

FEATURES:
Metal gear shafts
Metal and plastic primary differential

INCLUDES:
Main differential with steel ring gear
Planetary equipments and shafts
Sun equipments and shafts
Silicone grease

REQUIRES:
Installation on the car

REMARKS:
For primary differential w/ steel ring - TRAC6380
World gear shafts - TRAC6382
Silicon grease _- TRAC6037