Traxxas 5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building
Blue rubber dirt shields

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside size: 3/16" (5mm)
Outdoors size: 7/16" (11mm)
Width: 5/32" (4mm)

Get this product to enhance the one you read about.

10 X 15 X 4Mm Ball Bearing (2) Blue Rubber Sheild Revo

This is a set of 10x15mm Ball Bearings for use on the Traxxas Revo.

FEATURES:
Steel Building
Shielded with blue rubber seals

CONSISTS OF:
Two Ball Bearings

NEEDS:
Assembly to vehicle

SPECS:
Inner Size: 10mm
External Size: 15mm
Side Density: 4mm

REMARKS:
These bearings are used to support the Main Clutch (one needed).

Regularly gotten with the product that you are presently reading about.

Teflon Washers 5 X 8Mm (20)

These are Replacement Washers from Traxxas.

FEATURES:
Black plastic construction.
Used on the axles and in the transmission.

INCLUDES:
(20) Washers

SPECS:
Size: 5x8mm
Density: 0.5mm

Regularly gotten with the product that you are presently reading about.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel building
_
Roll pin pre-installed

CONSISTS OF:
One slipper clutch set

SPECS:
Length: 1.98" (50mm)
Size: .21" ( 5mm)

REMARKS:
This part will fit both the requirement and XL version of the Rustler
or Stampede.

This is a wonderful enhancement to the product presently being discussed.

Front Bearing Carriers, For Slash 2Wd, Nitro Slash, E-Rustler &

These are Optional Front Bearing Providers for the Traxxas Electric
Rustler, Stampede and Outlaw

The Front axles fit into these bearing carriers.

FEATURES:
Black nylon building

CONSISTS OF:
Two Front bearing (center) providers
Two RPM decals

NEEDS:
(4) 5x11mm bearings, if needed use (2) DTXC1547.

This is a wonderful enhancement to the product presently being discussed.

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Heavy Duty Driveshaft Assembly for the Slash 4x4 from Traxxas

FUNCTIONS:
Black plastic and steel building

CONSISTS OF:
Rear driveshaft assembly
Screw pin

NEEDS:
Setup on vehicle

You will certainly enjoy this item if you have the item above discussed.

30T Idler Gear Steel

This is the optional Steel Idler Equipment for lots of Traxxas Vehicles.

FEATURES:
Steel building

CONSISTS OF:
One steel 30T idler gear

NEEDS:
Setup on vehicle

This product praises the main item here.

Steel Top Drive Gear 22T

This is the 22 tooth, solidified steel leading drive gear that fits several Traxxas
automobiles. .
Includes: 1 gear just

You will certainly enjoy this item if you have the item above discussed.

Rear Bearing Carriers, For Traxxas Slash 2Wd, E-Rustler, E-Stamp

These are Optional Rear Bearing Carriers for the Traxxas Electric
Rustler, Stampede and Bandit.
The rear axles fit into these bearing carriers.

FEATURES:
Black nylon building

CONSISTS OF:
Two rear bearing (center) providers
Two RPM decals

NEEDS:
(4) 5x11mm bearings, if needed use (2) DTXC1547.

SPECS:
Height: 40mm (1.58")
Width at best point: 15.4mm (0.61")

You will certainly enjoy this item if you have the item above discussed.

Planetary Gear Diff W/Steel Ring Gear Slash/Bandit /Stampe

This is the Complete Planetary Equipment Differential With Steel Ring Equipment
for the Traxxas Outlaw, Stampede and Rustler.

FEATURES:
Metal gear shafts
Metal and plastic primary differential

CONSISTS OF:
Main differential with steel ring gear
Planetary equipments and shafts
Sun equipments and shafts
Silicone grease

NEEDS:
Setup on the vehicle

REMARKS:
For primary differential w/ steel ring - TRAC6380
Planet gear shafts - TRAC6382
Silicon grease _- TRAC6037