Traxxas 5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building
Blue rubber dirt guards

INCLUDES:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside diameter: 3/16" (5mm)
Outside diameter: 7/16" (11mm)
Width: 5/32" (4mm)

Get this thing to improve the one you are reading around.

10 X 15 X 4Mm Ball Bearing (2) Blue Rubber Sheild Revo

This is a set of 10x15mm Ball Bearings for use on the Traxxas Revo.

FEATURES:
Steel Construction
Shielded with blue rubber seals

INCLUDES:
2 Ball Bearings

NEEDS:
Assembly to automobile

SPECIFICATIONS:
Inner Diameter: 10mm
External Diameter: 15mm
Side Thickness: 4mm

COMMENTS:
These bearings are utilized to support the Primary Clutch (one needed).

Regularly acquired with the thing that you are presently reading about.

Teflon Washers 5 X 8Mm (20)

These are Replacement Washers from Traxxas.

FEATURES:
Black plastic construction.
Used on the axles and in the transmission.

INCLUDES:
(20) Washers

SPECIFICATIONS:
Size: 5x8mm
Thickness: 0.5mm

Regularly acquired with the thing that you are presently reading about.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel building
_
Roll pin pre-installed

INCLUDES:
One slipper clutch set

SPECIFICATIONS:
Length: 1.98" (50mm)
Diameter: .21" ( 5mm)

COMMENTS:
This part will fit both the requirement and XL variation of the Rustler
or Stampede.

This is a fantastic enhancement to the thing presently being gone over.

Front Bearing Carriers, For Slash 2Wd, Nitro Slash, E-Rustler &

These are Optional Front Bearing Providers for the Traxxas Electric
Rustler, Stampede and Bandit

The Front axles fit into these bearing carriers.

FEATURES:
Black nylon building

INCLUDES:
2 Front bearing (hub) carriers
2 RPM decals

NEEDS:
(4) 5x11mm bearings, if needed use (2) DTXC1547.

This is a fantastic enhancement to the thing presently being gone over.

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Strong Driveshaft Assembly for the Slash 4x4 from Traxxas

FEATURES:
Black plastic and steel building

INCLUDES:
Rear driveshaft assembly
Screw pin

NEEDS:
Setup on automobile

You will enjoy this thing if you have the thing previously stated.

30T Idler Gear Steel

This is the optional Steel Idler Gear for many Traxxas Vehicles.

FEATURES:
Steel building

INCLUDES:
One steel 30T idler equipment

NEEDS:
Setup on automobile

This thing compliments the main item below.

Steel Top Drive Gear 22T

This is the 22 tooth, hardened steel leading drive equipment that fits a number of Traxxas
vehicles. .
Consists of: 1 equipment just

You will enjoy this thing if you have the thing previously stated.

Rear Bearing Carriers, For Traxxas Slash 2Wd, E-Rustler, E-Stamp

These are Optional Back Bearing Carriers for the Traxxas Electric
Rustler, Stampede and Bandit.
The rear axles fit into these bearing carriers.

FEATURES:
Black nylon building

INCLUDES:
2 rear bearing (hub) carriers
2 RPM decals

NEEDS:
(4) 5x11mm bearings, if needed use (2) DTXC1547.

SPECS:
Height: 40mm (1.58")
Width at largest point: 15.4mm (0.61")

You will enjoy this thing if you have the thing previously stated.

Planetary Gear Diff W/Steel Ring Gear Slash/Bandit /Stampe

This is the Total Planetary Gear Differential With Steel Ring Gear
for the Traxxas Bandit, Stampede and Rustler.

FEATURES:
Metal equipment shafts
Metal and plastic main differential

INCLUDES:
Main differential with steel ring equipment
Planetary equipments and shafts
Sun equipments and shafts
Silicone grease

NEEDS:
Setup on the automobile

COMMENTS:
For main differential w/ steel ring - TRAC6380
Planet equipment shafts - TRAC6382
Silicon grease _- TRAC6037